noper
Becerikli
- Katılım
- 16 Ocak 2026
- Mesajlar
- 84
- Çözümler
- 1
- Beğeniler
- 43
Cihazın içini açmak çok basit ve kullanıcı dostu. Altında 2 vida, arkasında 2 vida toplam 4 vida var. Vidalar etiketin altında değiller açıktalar. Kullanılmayan bir kredi kartı ile kolayca açılıyor. UART pinleri lehimli değil fakat rx tx vcc gnd bilgisi kart üzerine yazılmış. 4 tane anten var. "Realtek 9607F ENG Board" cümlesi bootlogda geçiyor. Cihaz baştan aşağıya Realtek. Openwrt portlamak zor. Cihazın dosyaları arasında "Sagem" logosu var. Web arayüzünden config dosyası indirilebiliyor. Şifresi "tecomtec" , config değiştirilip yüklenirse SSH erişimi sağlanıyor ama kısıtlı. Cihazda 2 markanın da ismi geçiyor. Şaşırtıcı olacak ama cihazda GPON sürücüleri yüklü. Galiba anakartın dahili GPON girişli varyantları var. Şuan başka bir router üzerinde çalışıyorum işim biterse bununla uğraşacağım. Donanım ve bootlog bilgisi şu şekilde:
UART bootlog:
| Model | Aidata WR854GVR |
| Yazılım sürümü | V4.0.18_260920 (A slotu, çalışan) · V4.0.18_260814 (B slotu, yedek) |
| Kernel | Linux 5.10.70 #11 SMP |
| Çip | Realtek 9607F "Elnath" = RTL8198E (U-Boot board adı), Cortina ASIC ailesi |
| CPU | 2× ARM Cortex-A55 @ 1.2 GHz (0x412fd050), SMP |
| Secure Boot | Yok — ROTPK undeployed (BL1/BL2/BL31 hepsinde); imza doğrulaması devrede değil |
| RAM | 512 MiB DDR3 |
| SPI NAND | HeYangTek HYF4GQ4UAACAE (ID 0xc954), 512 MiB |
| Ethernet | 3×1GE LAN + 1×1GE WAN; dış GPHY RTL8221B |
| VoIP | SLIC: Slicecorp Vp886 via SPI/PCM, 1×FXS |
| 5 GHz Wi-Fi | RTL8852CE, Wi-Fi 6, band_cap:5G, macid 128; sürücü rtk_wifi6 v2.2.1.8 |
| 2.4 GHz Wi-Fi | RTL8192XB-E (bazband flashRTW), band_cap:2G |
| USB | xHCI: 1× USB 3.0 SuperSpeed |
| SSH | kapalı (açılabilir: config ACC_TBL.ssh=2 ile çalıştı) |
UART bootlog:
Kod:
NOTICE: Booting Trusted Firmware - Realtek Semiconductor Corp.
NOTICE: BL1: v1.5(release):ELNATH_TAPEOUT_1_0
NOTICE: BL1: Built : 19:19:58, Nov 11 2022
NOTICE: BL1: CPU Speed 1200 MHz
NOTICE: BL1: GLOBAL_STRAP 0xc06
NOTICE: boot-strap from serial NAND flash
NOTICE: BL1: SPI_NAND: Unknown ID --> 0xc954
WARNING: BL1: SPI_NAND: Could not find valid ONFI parameter page; aborting (0xff ff ff ff)
NOTICE: BL1: SPI_NAND: [bootstrap] page:0x800, block:0x20000
NOTICE: BL1: Platform initialized
NOTICE: ROTPK undeployed
NOTICE: BL1: Booting BL2
NOTICE: BL2: RTL8198E CPU Speed 1200 MHz
NOTICE: boot-strap from serial NAND flash
NOTICE: BL2: SNAND: Unknown ID --> 0xc954
WARNING: BL2: SNAND: Could not find valid ONFI parameter page; aborting (0xff ff ff ff)
NOTICE: BL2: SNAND: [bootstrap] page:0x800, block:0x20000
WARNING: BL2: SNAND: Unknown ECC criteria, bypass On-Die ECC decode status
## DRAM init.(ELNATH): V1.4.5 ##
INFO: PKG=LQFP
INFO: DDR3: freq=1066, dq=16, sys clk=25MHz, DV=0x242
INFO: RZQ: RZQ_480CODE=0x10
INFO: ZQ: CK , OCD=0x114, ODT=0x028 PAD_ZCTRL=0x150c1f12
INFO: ZQ: CA , OCD=0x014, ODT=0x010 PAD_ZCTRL=0x09050b06
INFO: ZQ: DQ , OCD=0x030, ODT=0x014 PAD_ZCTRL=0x0b06180e
INFO: ZQ: DQS , OCD=0x114, ODT=0x014 PAD_ZCTRL=0x0b061f12
INFO: ZQ: DQS_H, OCD=0x11e, ODT=0x010 PAD_ZCTRL=0x09052415
INFO: ZQ: DQS_L, OCD=0x020, ODT=0x008 PAD_ZCTRL=0x0603120a
INFO: DRAM refresh time is 7800 ns
INFO: =Write leveling=
INFO: (TX) Write leveling CK PI right move 1
INFO: (TX) DQS_0 PI right moves 2
INFO: (TX) DQS_1 PI right moves 2
INFO: =DQS_0 gating training= TM_DQS_EN=7
INFO: =DQS_1 gating training= TM_DQS_EN=7
INFO: =RX DQS delay scan=
INFO: Rising Falling
INFO: (RX) DQ00 01~21 set 11, 02~21 set 11
INFO: (RX) DQ01 04~22 set 13, 04~23 set 13
INFO: (RX) DQ02 03~22 set 12, 03~23 set 13
INFO: (RX) DQ03 02~22 set 12, 04~22 set 13
INFO: (RX) DQ04 04~22 set 13, 04~23 set 13
INFO: (RX) DQ05 04~23 set 13, 04~24 set 14
INFO: (RX) DQ06 03~22 set 12, 03~23 set 13
INFO: (RX) DQ07 04~23 set 13, 04~23 set 13
INFO: (RX) DQ08 01~21 set 11, 02~21 set 11
INFO: (RX) DQ09 02~22 set 12, 02~21 set 11
INFO: (RX) DQ10 02~21 set 11, 02~21 set 11
INFO: (RX) DQ11 02~22 set 12, 02~21 set 11
INFO: (RX) DQ12 03~22 set 12, 02~22 set 12
INFO: (RX) DQ13 03~23 set 13, 04~21 set 12
INFO: (RX) DQ14 03~22 set 12, 03~22 set 12
INFO: (RX) DQ15 02~22 set 12, 02~22 set 12
INFO: =tm_rd_fifo training= tm_rd_fifo=4 (default=6)
INFO: (TX) DQ0 PI from 5 to 16, midpoint(-1) is 9 (default=9)
INFO: (TX) DQ1 PI from 4 to 16, midpoint(-1) is 9 (default=9)
INFO: DRAM size = 4Gb
INFO: BSTC test PASS
INFO: DDR init done, DRAM test PASS
NOTICE: BL2: v1.5(release):g181bb5b5c-dirty
NOTICE: BL2: Built : 15:04:18, Nov 28 2024
NOTICE: ROTPK undeployed
NOTICE: BL1: Booting BL31
NOTICE: BL31: v1.5(release):g59476ab7a
NOTICE: BL31: Built : 15:01:35, Nov 28 2024
WARNING: Using deprecated integer interrupt arrays in gicv3_driver_data_t
WARNING: Please migrate to using interrupt_prop_t arrays
NOTICE: boot-strap from serial NAND flash
NOTICE: BL31: SNAND: Unknown ID --> 0xc954
WARNING: BL31: SNAND: Could not find valid ONFI parameter page; aborting (0xff ff ff ff)
NOTICE: BL31: SNAND: [bootstrap] page:0x800, block:0x20000
WARNING: BL31: SNAND: Unknown ECC criteria, bypass On-Die ECC decode status
NOTICE: ROTPK undeployed
NOTICE: BL31: SECURE DRAM SIZE is 0x00040000
U-Boot 2022.10-00299-ge586de9330f (Feb 20 2026 - 17:11:06 +0800)Elnath-SoC
Board: RTL8198E
CortexA55: 1200 MHz
DRAM: DDR3-2134: 16-bit mode, 512 MiB
board_init(198):000000001e50b1d0
Core: 2 devices, 2 uclasses, devicetree: separate
NAND:
SPI NAND: HYF4GQ4UAACAE (0xc954)
spare: 0x80 (128B)
page: 0x800 (2KB)
block: 0x20000 (128KB)
chip: 0x20000000(512MB)
available: 0x1ff40000(511MB)
mode: F/S
clock: 100 MHz
BBL: Bbl0 from flash
Hidden: 0x1000000 0x4140000 0x7200000 0xa0e0000 0x11720000 0x1ff60000
NAND: 511 MiB
Loading Environment from NAND... OK
In: uart@f43291c0
Out: uart@f43291c0
Err: uart@f43291c0
Hit any key to stop autoboot: 1 0
ubi0: default fastmap pool size: 200
ubi0: default fastmap WL pool size: 100
ubi0: attaching mtd5
ubi0: scanning is finished
ubi0: attached mtd5 (name "ubi_device", size 501 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 4014, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1399833483
ubi0: available PEBs: 2136, total reserved PEBs: 1878, PEBs reserved for bad PEB handling: 80
Read 6291456 bytes from volume ubi_k0 to 0000000005000000
## Checking Image at 05000000 ...
FIT image found
FIT description: fitImage for RTK aarch64 kernel
Image 0 (kernel)
Description: Linux Kernel
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x050000e8
Data Size: 4593769 Bytes = 4.4 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Image 1 (fdt-0-intddr)
Description: FDT blob
Type: Flat Device Tree
Compression: lzma compressed
Data Start: 0x05461a00
Data Size: 5857 Bytes = 5.7 KiB
Architecture: AArch64
Load Address: 0x01800000
Image 2 (fdt-1-extddr)
Description: FDT blob
Type: Flat Device Tree
Compression: lzma compressed
Data Start: 0x0546316c
Data Size: 5855 Bytes = 5.7 KiB
Architecture: AArch64
Load Address: 0x01800000
Image 3 (script)
Description: script
Type: Script
Compression: uncompressed
Data Start: 0x054648c8
Data Size: 19 Bytes = 19 Bytes
Default Configuration: 'conf-0-intddr'
Configuration 0 (conf-0-intddr)
Description: FDT blob for 0-intddr
Kernel: kernel
FDT: fdt-0-intddr
Configuration 1 (conf-1-extddr)
Description: FDT blob for 1-extddr
Kernel: kernel
FDT: fdt-1-extddr
## Checking hash(es) for FIT Image at 05000000 ...
Hash(es) for Image 0 (kernel):
Hash(es) for Image 1 (fdt-0-intddr):
Hash(es) for Image 2 (fdt-1-extddr):
Hash(es) for Image 3 (script):
## Loading kernel from FIT Image at 05000000 ...
Using 'conf-0-intddr' configuration
Trying 'kernel' kernel subimage
Description: Linux Kernel
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x050000e8
Data Size: 4593769 Bytes = 4.4 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Verifying Hash Integrity ... OK
## Loading fdt from FIT Image at 05000000 ...
Using 'conf-0-intddr' configuration
Trying 'fdt-0-intddr' fdt subimage
Description: FDT blob
Type: Flat Device Tree
Compression: lzma compressed
Data Start: 0x05461a00
Data Size: 5857 Bytes = 5.7 KiB
Architecture: AArch64
Load Address: 0x01800000
Verifying Hash Integrity ... OK
Loading fdt from 0x05461a00 to 0x01800000
Uncompressing Flat Device Tree
Booting using the fdt blob at 0x1800000
Uncompressing Kernel Image
Loading Device Tree to 000000001e4fa000, end 000000001e504995 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 5.10.70 (ronghua_xing@apserver85) (aarch64-linux-gcc (Realtek ASDK64-10.4.1 Build 3796) 10.4.1 20220712, GNU ld (Realtek ASDK64-10.4.1 Build 3796) 2.35.2.20210110) #11 SMP Sun Sep 20 15:39:18 CST 2026
[ 0.000000] Machine model: Realtek 9607F ENG Board
[ 0.000000] earlycon: serial0 at MMIO 0x00000000f43291c0 (options '')
[ 0.000000] printk: bootconsole [serial0] enabled
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000290ffff]
[ 0.000000] node 0: [mem 0x0000000002910000-0x00000000029d0fff]
[ 0.000000] node 0: [mem 0x00000000029d2000-0x0000000002fdffff]
[ 0.000000] node 0: [mem 0x0000000002fe0000-0x0000000002febfff]
[ 0.000000] node 0: [mem 0x0000000002fec000-0x000000001fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] On node 0, zone Normal: 1 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 30 pages/cpu s84376 r8192 d30312 u122880
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: patching kernel code
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129023
[ 0.000000] Kernel command line: earlycon=serial,0xf43291c0 console=ttyS0,115200 ubi.mtd=4 root=31:8 rootfstype=squashfs swiotlb=noforce mtdparts=ca_spinand_flash:2048K(boot),256K@0x280000(env),256K@0x2C0000(env2),256K@0x300000(static_conf),513792K@0x340000(ubi_device)
[ 0.000000] printk: log_buf_len individual max cpu contribution: 131072 bytes
[ 0.000000] printk: log_buf_len total cpu_extra contributions: 131072 bytes
[ 0.000000] printk: log_buf_len min size: 131072 bytes
[ 0.000000] printk: log_buf_len: 262144 bytes
[ 0.000000] printk: early log buf free: 128536(98%)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 471016K/524284K available (9598K kernel code, 1308K rwdata, 2516K rodata, 2048K init, 643K bss, 53268K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 128 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000004f8040000
[ 0.000000] realtek,elnath-per-ictl init!
[ 0.000000] ni_ptp_ictl@0xf430439c: unable to get resource
[ 0.000000] random: get_random_bytes called from start_kernel+0x2f4/0x40c with crng_init=0
[ 0.000000] RTK SOC: soc_clks_setup finished.
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[ 0.000004] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[ 0.008203] Console: colour dummy device 80x25
[ 0.012491] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.022825] pid_max: default: 32768 minimum: 301
[ 0.027525] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.034729] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.043641] rcu: Hierarchical SRCU implementation.
[ 0.049183] smp: Bringing up secondary CPUs ...
[ 0.053945] Detected VIPT I-cache on CPU1
[ 0.053979] GICv3: CPU1: found redistributor 100 region 0:0x00000004f8060000
[ 0.054021] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.054129] smp: Brought up 1 node, 2 CPUs
[ 0.075623] SMP: Total of 2 processors activated.
[ 0.080309] CPU features: detected: Privileged Access Never
[ 0.085874] CPU features: detected: User Access Override
[ 0.091170] CPU features: detected: 32-bit EL0 Support
[ 0.096297] CPU features: detected: Common not Private translations
[ 0.102551] CPU features: detected: RAS Extension Support
[ 0.107942] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.116531] CPU features: detected: CRC32 instructions
[ 0.121667] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.128675] CPU: All CPU(s) started at EL2
[ 0.133740] devtmpfs: initialized
[ 0.141838] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.151546] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.158439] pinctrl core: initialized pinctrl subsystem
[ 0.163999] NET: Registered protocol family 16
[ 0.168750] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.176293] thermal_sys: Registered thermal governor 'step_wise'
[ 0.176808] cpuidle: using governor ladder
[ 0.186823] cpuidle: using governor menu
[ 0.190742] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.197516] ASID allocator initialised with 65536 entries
[ 0.217584] reg-rtk_spare f43294b0.spare: resource - [mem 0xf43294b0-0xf43294b3 flags 0x200] mapped at 0x(____ptrval____)
[ 0.249545] iommu: Default domain type: Translated
[ 0.254463] SCSI subsystem initialized
[ 0.258781] usbcore: registered new interface driver usbfs
[ 0.264191] usbcore: registered new interface driver hub
[ 0.271415] usbcore: registered new device driver usb
[ 0.278211] clocksource: Switched to clocksource arch_sys_counter
[ 0.308580] NET: Registered protocol family 2
[ 0.312909] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.320640] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.328922] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.336581] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.343756] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.350144] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.356523] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.363667] NET: Registered protocol family 1
[ 0.367878] PCI: CLS 0 bytes, default 64
[ 0.372215] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[ 0.381564] Initialise system trusted keyrings
[ 0.386003] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[ 0.394660] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.400490] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.404799] fuse: init (API version 7.32)
[ 0.444534] Key type asymmetric registered
[ 0.448508] Asymmetric key parser 'x509' registered
[ 0.453346] io scheduler mq-deadline registered
[ 0.457846] io scheduler kyber registered
[ 0.461907] atomic64_test: passed
[ 0.465436] rtk-taurus-phy f43200cc.phy: resource - [mem 0xf43200cc-0xf43200eb flags 0x200] mapped at 0x(____ptrval____)
[ 0.476198] rtk-taurus-phy f43200cc.phy: resource - [mem 0xf432039c-0xf432039f flags 0x200] mapped at 0x(____ptrval____)
[ 0.488986] ca77xx-gpio f4329300.gpio-controller: resource - [mem 0xf4329300-0xf43293b3 flags 0x200] mapped at 0x(____ptrval____)
[ 0.500535] ca77xx-gpio f4329300.gpio-controller: id 0
[ 0.506267] ca77xx-gpio f4329300.gpio-controller: Setting up IRQs for GPIO bank 0
[ 0.514267] ca77xx-gpio f4329300.gpio-controller: Setting up IRQs for GPIO bank 1
[ 0.522285] ca77xx-gpio f4329300.gpio-controller: Setting up IRQs for GPIO bank 2
[ 0.530312] ca77xx-gpio f4329300.gpio-controller: Setting up IRQs for GPIO bank 3
[ 0.538314] ca77xx-gpio f4329300.gpio-controller: Setting up IRQs for GPIO bank 4
[ 0.546359] Realtek GPIO Driver for Flash Reload Default
[ 0.551721] ----[ rtk gpio ]--------------------------------
[ 0.557932] ca_soc f4320000.soc: Vendor ID: 0x8f3
[ 0.562539] ca_soc f4320000.soc: Chip ID: 0x6900
[ 0.567084] ca_soc f4320000.soc: Chip Rev: 66
[ 0.571449] ca_soc f4320000.soc: Chip Mode: 0x3281
[ 0.576196] ca_soc f4320000.soc: CPLL: 1200.00 MHZ
[ 0.580982] ca_soc f4320000.soc: EPLL: 2000.00 MHZ
[ 0.585748] ca_soc f4320000.soc: FPLL: 1600.00 MHZ
[ 0.590531] ca_soc f4320000.soc: CPU Clock: 1200.00 MHZ
[ 0.595725] ca_soc f4320000.soc: Core Clock: 333.33 MHZ
[ 0.600947] ca_soc f4320000.soc: LSAXI Clock: 200.00 MHZ
[ 0.606233] ca_soc f4320000.soc: HSAXI Clock: 400.00 MHZ
[ 0.611535] ca_soc f4320000.soc: PE Clock: 800.00 MHZ
[ 0.616556] ca_soc f4320000.soc: PE AXI Clock: 400.00 MHZ
[ 0.622728] elnath_pmx_request_gpio: pin:137 reg_off:0x10 bit_off:9
[ 0.629029] elnath_pmx_request_gpio: pin:140 reg_off:0x10 bit_off:12
[ 0.635240] elnath_pmx_request_gpio: pin:113 reg_off:0xc bit_off:17
[ 0.641798] ca77xx-reset f43200a0.reset-controller: resource - [mem 0xf43200a0-0xf43200a3 flags 0x200] mapped at 0x(____ptrval____)
[ 0.653616] ca77xx-reset f43200a4.reset-controller: resource - [mem 0xf43200a4-0xf43200a7 flags 0x200] mapped at 0x(____ptrval____)
[ 0.665416] pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: pinmux group:opt_group reg_off:0x4 bit_off:20
[ 0.675272] pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: conflicts gpiomux:13 reg_off:0x0 bit_off:13
[ 0.685072] pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: conflicts gpiomux:14 reg_off:0x0 bit_off:14
[ 0.694880] pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: conflicts gpiomux:15 reg_off:0x0 bit_off:15
[ 0.704741] ca77xx-reset f432009c.reset-controller: resource - [mem 0xf432009c-0xf432009f flags 0x200] mapped at 0x(____ptrval____)
[ 0.716840] ca77xx-reset f43200a8.reset-controller: resource - [mem 0xf43200a8-0xf43200ab flags 0x200] mapped at 0x(____ptrval____)
[ 0.796857] f43291c0.uart: ttyS0 at I/O 0x0 (irq = 24, base_baud = 7812500) is a Cortina UART0
[ 0.805769] printk: console [ttyS0] enabled
[ 0.805769] printk: console [ttyS0] enabled
[ 0.813976] printk: bootconsole [serial0] disabled
[ 0.813976] printk: bootconsole [serial0] disabled
[ 0.824036] f43291f0.uart: ttyS1 at I/O 0x0 (irq = 25, base_baud = 7812500) is a Cortina UART1
[ 0.833306] pe_ctrl_probe
[ 0.836153] IPC: host cpu is ARM , thisCPU=0x0
[ 0.840613] IPC: irq_reg_to_pe map reg 0x(____ptrval____)
[ 0.845997] IPC: irq_reg_from_pe map reg 0x(____ptrval____)
[ 0.851689] IPC: list physical start from: 0x2910000
[ 0.856596] IPC: list virtual start from: 0xffffffc012800000
[ 0.862250] IPC: list size: 0xc1800
[ 0.867470] IPC: Debug:...Clearing arm_pe0 memory.... from 0xffffffc012800000
[ 0.874733] IPC: Debug:...Clearing arm_pe1 memory.... from 0xffffffc012820400
[ 0.882000] IPC: Debug:...Clearing arm_pe2 memory.... from 0xffffffc012881000
[ 0.889264] IPC: version is 200
[ 0.892250] IPC: irq = 21
[ 0.895174] ca_pelog_probe
[ 0.897845] pelog0: shm physical address : 0x2fe0000
[ 0.902771] pelog0: shm virtual address : 0xffffffc0127b0000
[ 0.908406] pelog0: shm size: 0x4000
[ 0.911962] pelog0: reset magicNum
[ 0.915372] pelog1: shm physical address : 0x2fe4000
[ 0.920310] pelog1: shm virtual address : 0xffffffc0127b8000
[ 0.925950] pelog1: shm size: 0x4000
[ 0.929517] pelog1: reset magicNum
[ 0.932908] pelog2: shm physical address : 0x2fe8000
[ 0.937853] pelog2: shm virtual address : 0xffffffc0127c0000
[ 0.943511] pelog2: shm size: 0x4000
[ 0.947062] pelog2: reset magicNum
[ 0.950882] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.957208] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 0.963798] ca-qspi 4f4324000.sf-ctrl: RTK_BBL_OFFSET:0x200000
[ 0.969529] ca-qspi 4f4324000.sf-ctrl: ca-qspi resource - [mem 0x4f4324000-0x4f432404f flags 0x200] mapped at 0x(____ptrval____)
[ 0.981638] spi-nand spi0.0: model_name: HYF4GQ4UAACAE
[ 0.986615] spi-nand spi0.0: HeYangTek SPI NAND was found.
[ 0.992108] spi-nand spi0.0: 512 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 1.000271] spi_nand: proc entry /proc/spi_nand/info created
[ 1.787861] spi-nand: spi-nand: BBL OFFSET found at (0x00200000)
[ 1.793708] spi nand total capacity is 512MB(0x20000000)
[ 1.799005] spi nand available size is 511MB(0x1ff40000)
[ 1.804299] spi nand Bbl0 from flash
[ 1.807861] spi nand hidden:
[ 1.807863] 0x1000000
[ 1.810825] 0x4140000
[ 1.813161] 0x7200000
[ 1.815506] 0xa0e0000
[ 1.817852] 0x11720000
[ 1.820204] 0x1ff60000
[ 1.822630]
[ 1.826541] spi nand Mode: S/S
[ 1.829603] 5 cmdlinepart partitions found on MTD device ca_spinand_flash
[ 1.836358] Creating 5 MTD partitions on "ca_spinand_flash":
[ 1.842020] 0x000000000000-0x000000200000 : "boot"
[ 1.851164] 0x000000280000-0x0000002c0000 : "env"
[ 1.857348] 0x0000002c0000-0x000000300000 : "env2"
[ 1.863595] 0x000000300000-0x000000340000 : "static_conf"
[ 1.870487] 0x000000340000-0x00001f900000 : "ubi_device"
[ 2.645271] ca-qspi 4f4324000.sf-ctrl: spi-flash controller probed, while mode_bits=0x0000
[ 2.653733] spi-ca77xx f43290e8.spi: resource - [mem 0xf43290e8-0xf4329127 flags 0x200] mapped at 0x(____ptrval____)
[ 2.664175] spi-ca77xx f43290e8.spi: irq 54
[ 2.668284] spi-ca77xx f43290e8.spi: SPI HW CS 8
[ 2.674567] libphy: Fixed MDIO Bus: probed
[ 2.678550] Init xPON/Switch Driver Module....
[ 2.678561] OK
[ 2.684585] Init xPON/Switch Core Dev Module....
[ 2.684595] OK
[ 2.690841]
[ 2.690841] rtdrv_init !!!! for netfilter
[ 2.696404] [rtdrv_init]: rtdrv_ext_igmpHook_sockopts init.
[ 2.701967] [rtdrv_init]: rtdrv_ext_igmpHook_sockopts success.
[ 2.707816] pkt_redirect_init complete
[ 2.711536] interrupt broadcaster init ok!
[ 2.715601] [FCEXT] rtk_fc_extmodule_init
[ 2.719693] [nic_hook_init-213]
[ 2.722813] rtk_common_utility_init 533 common utility init!
[ 2.728565] PPP generic driver version 2.4.2
[ 2.733034] NET: Registered protocol family 24
[ 2.737338] PPTP driver version 0.8.5
[ 2.741331] usbcore: registered new interface driver asix
[ 2.746630] usbcore: registered new interface driver ax88179_178a
[ 2.752742] usbcore: registered new interface driver cdc_ether
[ 2.758537] usbcore: registered new interface driver net1080
[ 2.764161] usbcore: registered new interface driver cdc_subset
[ 2.770097] usbcore: registered new interface driver zaurus
[ 2.775640] usbcore: registered new interface driver cdc_ncm
[ 2.781464] taurus-usb2phy f432b020.usbphy: usb2_phy resource - [mem 0xf432b020-0xf432b037 flags 0x200] mapped at 0x(____ptrval____)
[ 2.793250] taurus-usb2phy f432b020.usbphy: USB2-port0 VBUS GPIO Resource Get O.K and u2port0_vbus:0
[ 2.802360] taurus-usb2phy f432b020.usbphy: Chip revision is 66 using params phy_data_verB
[ 2.810598] taurus-usb2phy f432b020.usbphy: USB2 port0 get phy_param0 OK
[ 2.817287] taurus-usb2phy f432b020.usbphy: USB2 port1 get phy_param0 OK
[ 2.878600] taurus-usb3phy f432b000.usbphy: usb3_phy resource - [mem 0xf432b000-0xf432b01f flags 0x200] mapped at 0x(____ptrval____)
[ 2.890398] taurus-usb3phy f432b000.usbphy: usb3_phy resource - [mem 0xf432b04c-0xf432b05b flags 0x200] mapped at 0x(____ptrval____)
[ 2.902306] elnath_pmx_request_gpio: pin:141 reg_off:0x10 bit_off:13
[ 2.908620] taurus-usb3phy f432b000.usbphy: USB3-port VBUS GPIO Resource Get O.K and vbus:0
[ 2.916965] taurus-usb3phy f432b000.usbphy: Chip revision is 66 using params phy_data_verB
[ 2.925359] taurus-usb3phy f432b000.usbphy: Enabled S3 u3port resource - [mem 0xf4338000-0xf4338fff flags 0x200] mapped at 0x(____ptrval____)
[ 2.958888] taurus-usb2phy f432b020.usbphy: USB2 PHY version: revB v1.0 (2024.06.12)
[ 2.966498] taurus-usb3phy f432b000.usbphy: USB3 PHY version: revB v1.0 (2023.07.03)
[ 3.078253] taurus-usb3phy f432b000.usbphy: calibration code: 1.
[ 3.085797] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.091394] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.099158] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe65 hci version 0x110 quirks 0x0000000000010010
[ 3.108450] xhci-hcd xhci-hcd.0.auto: irq 58, io mem 0xf0200000
[ 3.114414] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.119974] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.127482] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 3.134626] hub 1-0:1.0: USB hub found
[ 3.138290] hub 1-0:1.0: 2 ports detected
[ 3.142648] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.151191] hub 2-0:1.0: USB hub found
[ 3.154813] hub 2-0:1.0: 1 port detected
[ 3.159320] usbcore: registered new interface driver cdc_acm
[ 3.164820] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.172926] usbcore: registered new interface driver usblp
[ 3.178638] usbcore: registered new interface driver uas
[ 3.183869] usbcore: registered new interface driver usb-storage
[ 3.190011] usbcore: registered new interface driver usbserial_generic
[ 3.196422] usbserial: USB Serial support registered for generic
[ 3.202463] usbcore: registered new interface driver ch341
[ 3.207876] usbserial: USB Serial support registered for ch341-uart
[ 3.214176] usbcore: registered new interface driver cp210x
[ 3.219715] usbserial: USB Serial support registered for cp210x
[ 3.225625] usbcore: registered new interface driver cypress_m8
[ 3.231538] usbserial: USB Serial support registered for DeLorme Earthmate USB
[ 3.238742] usbserial: USB Serial support registered for HID->COM RS232 Adapter
[ 3.246021] usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter
[ 3.253370] usbcore: registered new interface driver ftdi_sio
[ 3.259073] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 3.266399] usbcore: registered new interface driver option
[ 3.271940] usbserial: USB Serial support registered for GSM modem (1-port)
[ 3.278946] usbcore: registered new interface driver pl2303
[ 3.284426] usbserial: USB Serial support registered for pl2303
[ 3.290334] i2c /dev entries driver
[ 3.293988] pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: pinmux group:i2c0_group reg_off:0x8 bit_off:16
[ 3.304023] ca77xx-i2c f4329170.i2c: resource - [mem 0xf4329170-0xf4329197 flags 0x200] mapped at 0x(____ptrval____)
[ 3.314469] ca77xx-i2c f4329170.i2c: invalid timeout on i2c@f4329170
[ 3.320793] ca77xx-i2c f4329170.i2c: invalid retries on i2c@f4329170
[ 3.327131] ca77xx-i2c f4329170.i2c: irq 27
[ 3.382154] ca77xx-i2c f4329198.i2c: resource - [mem 0xf4329198-0xf43291bf flags 0x200] mapped at 0x(____ptrval____)
[ 3.392591] ca77xx-i2c f4329198.i2c: invalid timeout on i2c@f4329198
[ 3.398888] ca77xx-i2c f4329198.i2c: invalid retries on i2c@f4329198
[ 3.405225] ca77xx-i2c f4329198.i2c: irq 28
[ 3.459989] cortina_thermal f4320294.thermal: Thermal Deviation: 2000
[ 3.766301] cortina_thermal f4320294.thermal: SoC Temperature=44140
[ 3.773513] [Kthread : luan_watchdog ] init complete!
[ 3.779774] elnath_pmx_request_gpio: pin:96 reg_off:0xc bit_off:0
[ 3.785890] elnath_pmx_request_gpio: pin:11 reg_off:0x0 bit_off:11
[ 3.792143] elnath_pmx_request_gpio: pin:99 reg_off:0xc bit_off:3
[ 3.798231] elnath_pmx_request_gpio: pin:139 reg_off:0x10 bit_off:11
[ 3.804603] elnath_pmx_request_gpio: pin:6 reg_off:0x0 bit_off:6
[ 3.810646] elnath_pmx_request_gpio: pin:12 reg_off:0x0 bit_off:12
[ 3.816829] elnath_pmx_request_gpio: pin:97 reg_off:0xc bit_off:1
[ 3.822931] elnath_pmx_request_gpio: pin:103 reg_off:0xc bit_off:7
[ 3.829101] elnath_pmx_request_gpio: pin:102 reg_off:0xc bit_off:6
[ 3.835227] elnath_pmx_request_gpio: pin:100 reg_off:0xc bit_off:4
[ 3.841431] elnath_pmx_request_gpio: pin:98 reg_off:0xc bit_off:2
[ 3.849456] /proc/enable_dos created
[ 3.852884] u32 classifier
[ 3.855559] input device check on
[ 3.859688] xt_time: kernel timezone is -0000
[ 3.863982] gre: GRE over IPv4 demultiplexor driver
[ 3.868766] ip_gre: GRE over IPv4 tunneling driver
[ 3.875043] Initializing XFRM netlink socket
[ 3.879516] NET: Registered protocol family 10
[ 3.884719] Segment Routing with IPv6
[ 3.888977] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.895989] [ip6tnl_fmr_proc_init:89] Create /proc/net/ip6_tunnel_fmr
[ 3.902312] NET: Registered protocol family 17
[ 3.906722] NET: Registered protocol family 15
[ 3.911234] Bridge firewalling registered
[ 3.915187] l2tp_core: L2TP core driver, V2.0
[ 3.919480] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.924226] 8021q: 802.1Q VLAN Support v1.8
[ 3.928609] [Kthread : rtk_tref] init complete!
[ 3.933243] Loading compiled-in X.509 certificates
[ 3.939155] cortina-pcie f4325000.pcie: resource - [mem 0xf4325000-0xf43253ff flags 0x200] mapped at 0xffffffc0111d5000
[ 3.949799] cortina-pcie f4325000.pcie: id 0
[ 3.954021] cortina-pcie f4325000.pcie: num-lanes 2
[ 3.958910] cortina-pcie f4325000.pcie: resource - [mem 0xf4333000-0xf4334fff flags 0x200] mapped at 0xffffffc0128c4000
[ 3.969657] cortina-pcie f4325000.pcie: Chip revision is 66 using params serdes-cfg-verB
[ 3.978053] cortina-pcie f4325000.pcie: resource - [mem 0xa0000000-0xa0000fff flags 0x200] mapped at 0xffffffc0111dd000
[ 3.988739] cortina-pcie f4325000.pcie: outbound iATU enable
[ 3.994327] cortina-pcie f4325000.pcie: host bridge /pcie@f4325000 ranges:
[ 4.001200] cortina-pcie f4325000.pcie: IO 0x00a0003000..0x00a0012fff -> 0x0000000000
[ 4.009514] cortina-pcie f4325000.pcie: MEM 0x00a0400000..0x00afffffff -> 0x00a0400000
[ 4.021914] cortina-pcie f4325000.pcie: PCIe Serdes CFG version: revB v1.1 (2024.06.04) modify
[ 4.155440] cortina-pcie f4325000.pcie: No BER Notify!
[ 4.262452] cortina-pcie f4325000.pcie: Link up
[ 4.266811] cortina-pcie f4325000.pcie: Speed Gen2 Lanes x1
[ 4.272529] cortina-pcie f4325000.pcie: PCI host bridge to bus 0000:00
[ 4.278910] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.284353] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 4.290524] pci_bus 0000:00: root bus resource [mem 0xa0400000-0xafffffff]
[ 4.297400] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400
[ 4.303384] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 4.310089] pci 0000:00:00.0: supports D1 D2
[ 4.314298] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 4.322070] pci 0000:01:00.0: [10ec:c852] type 00 class 0x028000
[ 4.327988] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 4.333587] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x000fffff 64bit]
[ 4.340698] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 4.359752] pci 0000:00:00.0: BAR 8: assigned [mem 0xa0400000-0xa04fffff]
[ 4.366377] pci 0000:00:00.0: BAR 6: assigned [mem 0xa0500000-0xa050ffff pref]
[ 4.373629] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 4.379690] pci 0000:01:00.0: BAR 2: assigned [mem 0xa0400000-0xa04fffff 64bit]
[ 4.386992] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 4.393044] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 4.398237] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff]
[ 4.404307] pci 0000:00:00.0: bridge window [mem 0xa0400000-0xa04fffff]
[ 4.411496] cortina-pcie f4327000.pcie: resource - [mem 0xf4327000-0xf43273ff flags 0x200] mapped at 0xffffffc0111e5000
[ 4.422156] cortina-pcie f4327000.pcie: id 2
[ 4.426364] cortina-pcie f4327000.pcie: num-lanes 1
[ 4.431267] cortina-pcie f4327000.pcie: resource - [mem 0xf4337000-0xf4337fff flags 0x200] mapped at 0xffffffc0111ed000
[ 4.442001] cortina-pcie f4327000.pcie: Chip revision is 66 using params serdes-cfg-verB
[ 4.450307] cortina-pcie f4327000.pcie: resource - [mem 0xc0000000-0xc0000fff flags 0x200] mapped at 0xffffffc0111f5000
[ 4.460967] cortina-pcie f4327000.pcie: outbound iATU enable
[ 4.466572] cortina-pcie f4327000.pcie: host bridge /pcie@f4327000 ranges:
[ 4.473446] cortina-pcie f4327000.pcie: IO 0x00c0003000..0x00c0012fff -> 0x0000000000
[ 4.481773] cortina-pcie f4327000.pcie: MEM 0x00c0400000..0x00cfffffff -> 0x00c0400000
[ 4.494164] cortina-pcie f4327000.pcie: PCIe Serdes CFG version: revB v1.1 (2024.06.04)
[ 4.508299] cortina-pcie f4327000.pcie: PCIE calibration val:0008
[ 4.518206] cortina-pcie f4327000.pcie: Link up
[ 4.522564] cortina-pcie f4327000.pcie: Speed Gen1 Lanes x1
[ 4.528282] cortina-pcie f4327000.pcie: PCI host bridge to bus 0001:00
[ 4.534642] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 4.540132] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 4.549054] pci_bus 0001:00: root bus resource [mem 0xc0400000-0xcfffffff]
[ 4.555933] pci 0001:00:00.0: [16c3:abcd] type 01 class 0x060400
[ 4.561915] pci 0001:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 4.568624] pci 0001:00:00.0: supports D1 D2
[ 4.572828] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 4.580527] pci 0001:01:00.0: [10ec:0192] type 00 class 0x028000
[ 4.586472] pci 0001:01:00.0: reg 0x10: [io 0x10000-0x100ff]
[ 4.592244] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x000fffff 64bit]
[ 4.599503] pci 0001:01:00.0: supports D1 D2
[ 4.603601] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 4.629726] pci 0001:00:00.0: BAR 8: assigned [mem 0xc0400000-0xc04fffff]
[ 4.636352] pci 0001:00:00.0: BAR 6: assigned [mem 0xc0500000-0xc050ffff pref]
[ 4.643594] pci 0001:00:00.0: BAR 7: assigned [io 0x10000-0x10fff]
[ 4.649821] pci 0001:01:00.0: BAR 2: assigned [mem 0xc0400000-0xc04fffff 64bit]
[ 4.657156] pci 0001:01:00.0: BAR 0: assigned [io 0x10000-0x100ff]
[ 4.663367] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 4.668557] pci 0001:00:00.0: bridge window [io 0x10000-0x10fff]
[ 4.674802] pci 0001:00:00.0: bridge window [mem 0xc0400000-0xc04fffff]
[ 4.683415] ubi0: default fastmap pool size: 200
[ 4.687869] ubi0: default fastmap WL pool size: 100
[ 4.692766] ubi0: attaching mtd4
[ 8.598438] ubi0: scanning is finished
[ 8.617584] ubi0: attached mtd4 (name "ubi_device", size 501 MiB)
[ 8.623544] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 8.630379] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 8.637142] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 8.644090] ubi0: good PEBs: 4014, bad PEBs: 0, corrupted PEBs: 0
[ 8.650171] ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[ 8.657366] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1399833483
[ 8.666485] ubi0: available PEBs: 2136, total reserved PEBs: 1878, PEBs reserved for bad PEB handling: 80
[ 8.676053] ubi0: background thread "ubi_bgt0d" started, PID 1250
[ 8.684935] elnath_pmx_request_gpio: pin:136 reg_off:0x10 bit_off:8
[ 8.691252] elnath_pmx_request_gpio: pin:112 reg_off:0xc bit_off:16
[ 8.697426] elnath_pmx_request_gpio: pin:111 reg_off:0xc bit_off:15
[ 8.703825] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 8.710924] CONFIG_SYSTEM_CAPABILITY is 0;3;1;2;1;1;0;1;0;0;0;0
[ 8.721277] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[ 8.731313] devtmpfs: mounted
[ 8.734971] Freeing unused kernel memory: 2048K
[ 8.758370] Run /sbin/init as init process
Bad inittab entry at line 34
starting pid 1300, tty '': '/etc/init.d/rcS'
=== Start to run rc0 / rc63 ===
----- do_rc [/etc/init.d/rc2] -----
WARN: conflicting configurations in /etc/fstab and /etc/default/rcS
regarding the writability of rootfs. Please fix one of them.
[ 10.572633] UBIFS (ubi0:7): Mounting in unauthenticated mode
[ 10.578343] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 1337
[ 10.639581] UBIFS (ubi0:7): recovery needed
[ 10.680074] UBIFS (ubi0:7): recovery completed
[ 10.684427] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "ubi_packets"
[ 10.692193] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.702090] UBIFS (ubi0:7): FS size: 40759296 bytes (38 MiB, 321 LEBs), journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 10.712512] UBIFS (ubi0:7): reserved for root: 1925161 bytes (1880 KiB)
[ 10.719117] UBIFS (ubi0:7): media format: w5/r0 (latest is w5/r0), UUID F6B98AE6-2D92-4A7E-9E85-57D220151A57, small LPT model
[ 10.739072] UBIFS (ubi0:0): Mounting in unauthenticated mode
[ 10.744703] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1340
[ 10.805692] UBIFS (ubi0:0): recovery needed
[ 10.978689] UBIFS (ubi0:0): recovery completed
[ 10.983048] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "ubi_Config"
[ 10.990716] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.000616] UBIFS (ubi0:0): FS size: 9269248 bytes (8 MiB, 73 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 11.010691] UBIFS (ubi0:0): reserved for root: 437809 bytes (427 KiB)
[ 11.017117] UBIFS (ubi0:0): media format: w5/r0 (latest is w5/r0), UUID 2894A7D4-D689-4495-A46E-D0B551E252C1, small LPT model
[scfg.txt]Copy /etc/scfg.txt to /var/config/.
----- do_rc [/etc/init.d/rc3] -----
[mib_init_mib_with_program_default:1966] Load from program default (type=2, action=2, range=0)!
WARNING: table_setting: Invalid table entry name: PON_MODE
[_load_xml_file:763] load from /etc/config_default_hs.xml (tmp_file=/tmp/cnftmp_jXmltQ, dtype=2)
[mib_init_mib_with_program_default:1966] Load from program default (type=8, action=2, range=0)!
WARNING: table_setting: Invalid table entry name: DUAL_MGMT_MODE
WARNING: table_setting: Invalid table entry name: OMCI_WAN_QOS_QUEUE_NUM
[_load_xml_file:763] load from /etc/config_default.xml (tmp_file=/tmp/cnftmp_IM2lyN, dtype=8)
WARNING: table_setting: Invalid table entry name: DUAL_MGMT_MODE
WARNING: table_setting: Invalid table entry name: OMCI_WAN_QOS_QUEUE_NUM
[_load_xml_file:763] load from /etc/province/config_factory.xml (tmp_file=/tmp/cnftmp_tjDMAQ, dtype=8)
[mib_init_mib_with_program_default:1966] Load from program default (type=1, action=2, range=0)!
[mib_init_mib_with_program_default:1966] Load from program default (type=2, action=2, range=0)!
WARNING: table_setting: Invalid table entry name: PON_MODE
[_load_xml_file:763] load from /etc/config_default_hs.xml (tmp_file=/tmp/cnftmp_HTSp2P, dtype=2)
[_load_xml_file:763] load from /var/config/config_hs.xml (tmp_file=/tmp/cnftmp_L7BVqQ, dtype=2)
[mib_init_mib_with_program_default:1966] Load from program default (type=8, action=2, range=0)!
WARNING: table_setting: Invalid table entry name: DUAL_MGMT_MODE
WARNING: table_setting: Invalid table entry name: OMCI_WAN_QOS_QUEUE_NUM
[_load_xml_file:763] load from /etc/config_default.xml (tmp_file=/tmp/cnftmp_n1eZDN, dtype=8)
[_load_xml_file:763] load from /var/config/config.xml (tmp_file=/tmp/cnftmp_AIxjJO, dtype=8)
[mib_init_mib_with_program_default:1966] Load from program default (type=1, action=2, range=0)!
set_msgqueue_max_size:417> set msgqidds.msg_qbytes=36120 OK
set_msgqueue_max_size:417> set msgqidds.msg_qbytes=36120 OK
diable printk= 0 parameter is 1
RTK SoC: Elnath
default CFG_ID_PON_MAC_MODE of scfg is IGNORED(0xFF) ...
[ 12.536258] ca_plat_kernel: loading out-of-tree module taints kernel.
[ 12.545094] ca-log: init calog-ioctl-dev OK (max_level 9, default_level 4)
[ 12.551995] ca-pal: init ca_pal_ioctl OK
[ 12.556215] ca-peri:hw_timer irq 49 install
[ 12.569410] SCFG initialize start.
[ 12.572815] SCFG initialize done.
[ 12.940075] pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: pinmux group:mdio_group reg_off:0x8 bit_off:20
[ 12.950071] ca_ne:ca_ni_init_module_probe:4197: Cortina Network Interface Driver 0.0.1
[ 12.957910] ca_ni_init_module_probe: data.chip_revision=B
[ 12.963325] error: aal_pon_mac_mode_get FAIL, pon_mac_mode = 255.
[ 12.969497] ca_ne_reg_init: out of SRAM range 0x(____ptrval____) NE driver initialized failed!!!
[ 12.986253] [1;33;40m[WARNING] aal_l3qm_init_startup_config: nic rx WITHOUT allocate scatter(env: use_fbm 1, eq_rule 0, build_skb 0, budget 64) [0m
[ 13.045454] __eth_port_phy_init: port 4 get failed
[ 13.050084] __eth_port_phy_init: port 5 get failed
[ 13.054857] __eth_port_phy_init: port 6 get failed
[ 13.149642] ca_ni_init_module: platform_driver_register() return ret=0
[ 13.248685] FC mirror function is not ready!
/bin/sh: can't open '/etc/scripts/rtkbosa.sh'
None of PON/WAN mode activated.....
Loading modules: ca-ne ca-plat-kernel ca-sdk-cb libscfg [ 13.737855] [FCMGR] module init, detect 2 cpus online @rtk_fc_mgr_init(924)
[ 13.748659] fc_db.controlFuc.external_switch_en = 0 external_switch_port_offset = 0
[ 13.756156] fc_db.controlFuc.mem_leak_debug = 0 fc_db.controlFuc.vlan_filtering = 1
[ 13.763824] fc_db.controlFuc.special_fast_forward_mode = 0 fc_db.controlFuc.hwnat_customize = 0 fc_db.controlFuc.hwnat_customize_nptv6_sram_acc_v2 = 0
[ 13.778916] [HWNAT] rtk_9607f_init: #####ASICDRIVERVER: B##### @rtk_9607f_init(6099)
[ 13.786583] [HWNAT] rtk_9607f_init: #####Set keep_lspid_unchange to 1##### @rtk_9607f_init(6105)
[ 13.795454] [HWNAT] rtk_9607f_init: #####Set wan_rxsel to 2##### @rtk_9607f_init(6112)
[ 13.803444] [HWNAT] rtk_9607f_init: #####Set wan_ind to 1##### @rtk_9607f_init(6124)
[ 13.811265] [HWNAT] rtk_9607f_init: #####Set stg0tbl[0]mac_da_match_en to 0##### @rtk_9607f_init(6133)
[ 13.820649] [HWNAT] rtk_9607f_init: #####Set stg0tbl[1]mac_da_match_en to 0##### @rtk_9607f_init(6133)
[ 13.830028] [HWNAT] rtk_9607f_init: #####Set stg0tbl[2]mac_da_match_en to 0##### @rtk_9607f_init(6133)
[ 13.839411] [HWNAT] rtk_9607f_init: #####Set stg0tbl[3]mac_da_match_en to 0##### @rtk_9607f_init(6133)
[ 13.856094] [HWNAT] rtk_9607f_acl_init: ##### L2/L3 CLS initialization success.##### @rtk_9607f_acl_init(5961)
[ 13.866088] [HWNAT] rtk_9607f_init: #####Disable L2FE/L3FE QoS Decision##### @rtk_9607f_init(6192)
[ 13.875765] ca_ni_virtual_instance_open: cpu_idx 2 bypass open because PE offload is enabled
[ 13.884058] [HWNAT] Enable CPU port 0x12 @rtk_9607f_cpuport_init(4923)
[ 13.890568] ca_ni_virtual_instance_open: cpu_idx 3 bypass open because PE offload is enabled
[ 13.898987] [HWNAT] Enable CPU port 0x13 @rtk_9607f_cpuport_init(4923)
[ 13.905497] ca_ni_virtual_instance_open: cpu_idx 4 bypass open because PE offload is enabled
[ 13.913930] [HWNAT] Enable CPU port 0x14 @rtk_9607f_cpuport_init(4923)
[ 13.920448] ca_ni_virtual_instance_open: cpu_idx 5 bypass open because PE offload is enabled
[ 13.928872] [HWNAT] Enable CPU port 0x15 @rtk_9607f_cpuport_init(4923)
[ 13.935384] ca_ni_virtual_instance_open: cpu_idx 6 bypass open because PE offload is enabled
[ 13.943820] [HWNAT] Enable CPU port 0x16 @rtk_9607f_cpuport_init(4923)
[ 13.950335] ca_ni_virtual_instance_open: cpu_idx 7 bypass open because PE offload is enabled
[ 13.958760] [HWNAT] Enable CPU port 0x17 @rtk_9607f_cpuport_init(4923)
[ 13.965442] [HWNAT] rtk_9607f_flow_init: ##### hash fib bits width: flow(type-0) act_mask 0x140000 (224 bits), type-1 act_mask 0x0 (0 bits), default act_mask 0x4d0000 (90 bits) @rtk_9607f_flow_init(5522)
[ 13.983476] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 0 (RTK_9607F_FLOW_PROFILE_FLOW_5TUPLE), profile 0 hash_mask_idx = 0 @rtk_9607f_flow_hash_profile_init(5200)
[ 14.000058] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 1 (RTK_9607F_FLOW_PROFILE_FLOW_2TUPLE), profile 0 hash_mask_idx = 1 @rtk_9607f_flow_hash_profile_init(5243)
[ 14.016646] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 2 (RTK_9607F_FLOW_PROFILE_FLOW_MC), profile 0 hash_mask_idx = 2 @rtk_9607f_flow_hash_profile_init(5264)
[ 14.032893] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 2 (RTK_9607F_FLOW_PROFILE_FLOW_MC), profile 1 hash_mask_idx = 3 @rtk_9607f_flow_hash_profile_init(5305)
[ 14.049152] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 3 (RTK_9607F_FLOW_PROFILE_DEFAULT_DROP), profile 0 hash_mask_idx = 4 @rtk_9607f_flow_hash_profile_init(5373)
[ 14.065810] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 4 (RTK_9607F_FLOW_PROFILE_MC_WIFI_TX_AMSDU_OFLD), profile 0 hash_mask_idx = 5 @rtk_9607f_flow_hash_profile_init(5391)
[ 14.083252] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 5 (RTK_9607F_FLOW_PROFILE_DUALFRAG_OR_ESP), profile 0 hash_mask_idx = 6 @rtk_9607f_flow_hash_profile_init(5411)
[ 14.100177] [HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 5 (RTK_9607F_FLOW_PROFILE_DUALFRAG_OR_ESP), profile 1 hash_mask_idx = 7 @rtk_9607f_flow_hash_profile_init(5457)
[ 14.195026] [Common] Success to register ipc msg handler
[ 14.200274] [rtk wfo] Success to register ipc msg handler
[ 14.205729] [DE-AMSDU] Success to register ipc msg handler
[ 14.211361] RTK FleetConntrack Driver - core module init
[ 14.216574] - version3: dev.0.0 (00000000) 0000-00-00-0000
[ 14.222136] - mem usage 16368 KB (malloc:2767344 fc_db:13993584)
[ 14.228307] insert here, priority: 1, portmask 268435455, rx: (____ptrval____)
[ 14.235501] insert here, priority: 10, portmask 268435455, rx: (____ptrval____)
[ 14.242793] [nic_register_txfunc-3412] txfunc=(____ptrval____)
[ 14.248610] RTK FleetConntrack Driver - manager module init
[ 14.254158] - mem usage 115 KB (db:50176 nicrx_ipi:68352)
start modprobe wifi6 module!
[ 14.724774] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 14.745754] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
1 wait modprobe wifi6 module ok!
[ 16.362644] RTW: module init start
[ 16.365890] RTW: rtk_wifi6 v2.2.1.8 2024/09/20
[ 16.370372] RTW: build time: Sep 20 2026 15:39:18
[ 16.375088] RTW: RTL WFO inited (supported band 0x2)
[ 16.380209] RTW: rtk_wifi6 probing pci device "0000:01:00.0"...
[ 16.386035] rtk_wifi6 0000:01:00.0: enabling device (0000 -> 0003)
[ 16.392245] [rtw_dev_probe] dev_probe_num:1 padapter:0x0000000000000000 dev_id:0
2 wait modprobe w[ 16.400466] PHL: Use chip layer register read functions!
ifi6 module ok!
[ 16.406373] PHL: [MAC] MAC_AX_MAJOR_VER = 0
[ 16.406373] MAC_AX_PROTOTYPE_VER = 27
[ 16.406373] MAC_AX_SUB_VER = 110
[ 16.406373] MAC_AX_SUB_INDEX = 0
[ 16.423660] RTW: ERROR RFE type can not be set for non single band device.
[ 16.430429] RTW: CONFIG_WLAN0_RFE_TYPE_53
[ 16.434370] RTW: rtw_load_phy_file_path(0) Parameter path: "/etc/conf/rtl8852ce/RFE50/"
[ 16.442368] RTW: 0000:01:00.0: initialize #7 handler "CORE RX" T@2/2
[ 16.448695] RTW: 0000:01:00.0: initialize #8 handler "PHL SER" T@2/2
[ 16.455241] RTW: 0000:01:00.0: initialize #5 handler "PHL TX" T@2/2
[ 16.461367] RTW: 0000:01:00.0: initialize #6 handler "PHL RX" T@2/2
[ 16.467585] RTW: 0000:01:00.0: initialize #9 handler "PHL PE RX" T@2/2
[ 16.474692] PHL: [RXBUF][dev_id:0][ch:0] rxbd_num:256 buf_len:2048
[ 16.480762] PHL: [RXBUF][dev_id:0][ch:1] rxbd_num:64 buf_len:512
[ 16.486702] PHL: [RXBUF][dev_id:0][ch:0] rx_buf: num=768 size=11460
[ 16.495480] PHL: CH[0] Alloc 11460B RX buffer, got available size 16000B
[ 16.502053] PHL: [RXBUF][dev_id:0][ch:1] rx_buf: num=128 size=192
[ 16.508388] PHL: CH[1] Alloc 192B RX buffer, got available size 640B
[ 16.517620] PHL: RP agg is 121 for 640.
[ 16.521648] PHL: hal_cfg_fw_8852c : fw_en 1.
[ 16.528372] PHL: [MAC] [ERR]Access efuse in suspend
[ 16.537349] PHL: [MAC] efuse_fv = 0xff
[ 16.540932] PHL: [MAC] [MAC-INFO]- CV : 1
[ 16.544918] PHL: [MAC] [MAC-INFO]- FV : 1
[ 16.551226] PHL: [MAC] efuse_aid = 0xffff
[ 16.555060] PHL: [MAC] [MAC-INFO]- AID : 6758
[ 16.559560] PHL: [MAC] Clear all bd index done.
[ 16.564001] PHL: [MAC] [FWDL] FW INIT......................................START
[ 16.571303] PHL: [MAC] Downloading Chip Halmac ID: 0x02
[ 16.576502] PHL: [MAC] [FWDL] Query Internal FW Chip_ID = 0x2
[ 16.582237] PHL: [MAC] [FWDL] Query Internal FW CV = 0x1
[ 16.587526] PHL: [MAC] [FWDL] Query Internal FW cat = 0x2
[ 16.592926] PHL: [MAC] [FWDL] WCPU OFF......................................DONE
[ 16.600291] PHL: [MAC] [FWDL] WCPU FWDL Boot.
[ 16.606786] PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
[ 16.611764] PHL: [MAC] [FWDL] WCPU FW BIN CHECK.............................DONE
[ 16.619137] PHL: [MAC] [FWDL] WCPU PRE BOOT..................................DONE
[ 16.626623] PHL: [MAC] [FWDL] WCPU IMAGE HEADER SEND........................DONE
[ 16.633980] PHL: [MAC] [FWDL] SEC_0:Len=0x5F798,Addr=0x20100000,Type=0x2
[ 16.641682] PHL: [MAC] [FWDL] SEC_1:Len=0x1AF0,Addr=0x2015F798,Type=0x7
[ 16.648166] PHL: [MAC] [FWDL] SEC_2:Len=0x5CE0,Addr=0x2021B000,Type=0x1
[ 16.654818] PHL: [MAC] [FWDL] SEC_3:Len=0x3C0,Addr=0x20237C00,Type=0x9
[ 16.661276] PHL: [MAC] [FWDL] DLFW DONE (0x8)
[ 16.687430] PHL: [MAC] [FWDL] INIT SYSMIB ENTRY (0xA)
[ 16.692315] PHL: [MAC] [FWDL] WCPU RAM PATCH.................................DONE
[ 16.699779] PHL: [MAC] _____ _____ _ ___ _ ___ ___
[ 16.705848] PHL: [MAC] | __\ \ / / \| | | _ \/_\ / __/ __|
[ 16.712017] PHL: [MAC] | _| \ \/\/ /| |) | |__ | _/ _ \\__ \__ \
[ 16.718173] PHL: [MAC] |_| \_/\_/ |___/|____| |_|/_/ \_\___/___/
[ 16.724349] PHL: [MAC] [FWDL] OS START DONE (0x26)
[ 16.729132] PHL: [MAC] [FWDL] WCPU FREERTOS INIT.............................DONE
[ 16.736575] PHL: [MAC] ___ _____ ___ ___ ___ ___ ___ _____
[ 16.742744] PHL: [MAC] | _ |_ _/ _ \/ __| | _ )/ _ \ / _ |_ _|
[ 16.748994] PHL: [MAC] | / | || (_) \__ \ | _ | (_) | (_) || |
[ 16.755063] PHL: [MAC] |_|_\ |_| \___/|___/ |___/\___/ \___/ |_|
[ 16.761148] PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
[ 16.766264] PHL: [MAC] [FWDL] FW INIT.......................................DONE
[ 16.775862] RTW: [HW-CAP] ic_name:rtl8852c
[ 16.779823] RTW: [HW-CAP] macid_num:128
[ 16.783609] RTW: [HW-CAP] sec_cap:0x01
[ 16.787341] RTW: [HW-CAP] sec_cam_ent_num:0
[ 16.791526] RTW: [HW-CAP] rfpath_num_2g:2
[ 16.795500] RTW: [HW-CAP] rfpath_num_5g:2
[ 16.799502] RTW: [HW-CAP] rf_reg_path_num:2
[ 16.803659] RTW: [HW-CAP] max_tx_cnt:2
[ 16.807392] RTW: [HW-CAP] tx_nss_num:2
[ 16.811131] RTW: [HW-CAP] rx_nss_num:2
[ 16.814857] RTW: [HW-CAP] band_cap:5G
[ 16.818595] RTW: [HW-CAP] bw_cap:20M 40M 80M 160M
[ 16.823362] RTW: [HW-CAP] proto_cap:b g n ac ax
[ 16.827963] RTW: [HW-CAP] wl_func:P2P MIRACAST TDLS
[ 16.832923] RTW: 0000:01:00.0: initialize #2 handler "netif RX" T@0/2
[ 16.839405] load default 5g thermal parameters
[ 16.844317] eric-tx CALL alloc_txring !!!!
[ 16.851219] swq tasklet init padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.858241] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.863887] RTW: ERROR rtw_hw_get_mac_addr failed
[ 16.868544] RTW: ERROR invalid mac addr:00:00:00:00:00:00, assign random MAC
[ 16.875566] RTW: Creating #5 virtual interface(s).
[ 16.880541] eric-tx CALL alloc_txring !!!!
[ 16.884497] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.890308] eric-tx CALL alloc_txring !!!!
[ 16.894260] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.900067] eric-tx CALL alloc_txring !!!!
[ 16.904017] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.909837] eric-tx CALL alloc_txring !!!!
[ 16.913803] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.919587] eric-tx CALL alloc_txring !!!!
[ 16.923535] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 16.929333] RTW: rtw_cfg80211_init_ht_capab: band_type=0x2 dev_id=0x0 ht_cap->cap=1862
[ 16.937096] RTW: [rtw_build_he_supp_mcs] info_len:8
[ 16.941957] RTW: [rtw_build_he_supp_mcs] info_len:8
[ 16.947161] RTW: rtw_ndev_init(wlan0) if1 mac_addr=02:00:00:00:00:01
[ 16.954923] reg_therctl_ops(): reg wlan0 as idx 0
[ 16.959541] RTW: RTL WFO IPC (12) created
[ 16.972317] genirq: irq_chip PCI-MSI did not update eff. affinity mask of irq 73
[ 16.979890] RTW: rtk_wifi6 probing pci device "0001:01:00.0"...
[ 16.985727] rtk_wifi6 0001:01:00.0: enabling device (0000 -> 0003)
[ 16.991989] [rtw_dev_probe] dev_probe_num:2 padapter:0x0000000000000000 dev_id:1
[ 17.000175] PHL: Use chip layer register read functions!
[ 17.005331] PHL: [MAC] MAC_AX_MAJOR_VER = 0
[ 17.005331] MAC_AX_PROTOTYPE_VER = 27
[ 17.005331] MAC_AX_SUB_VER = 110
[ 17.005331] MAC_AX_SUB_INDEX = 0
[ 17.021148] RTW: CONFIG_WLAN1_RFE_TYPE_50
[ 17.025005] RTW: CONFIG_WLAN1_RFE_TYPE_50
[ 17.029047] RTW: rtw_load_phy_file_path(1) Parameter path: "/etc/conf/rtl8192xbe/RFE50/"
[ 17.037068] RTW: 0001:01:00.0: initialize #7 handler "CORE RX" T@2/2
[ 17.043409] RTW: 0001:01:00.0: initialize #8 handler "PHL SER" T@2/2
[ 17.049956] RTW: 0001:01:00.0: initialize #5 handler "PHL TX" T@2/2
[ 17.056050] RTW: 0001:01:00.0: initialize #6 handler "PHL RX" T@2/2
[ 17.062316] RTW: 0001:01:00.0: initialize #9 handler "PHL PE RX" T@2/2
[ 17.069405] PHL: [RXBUF][dev_id:1][ch:0] rxbd_num:256 buf_len:2048
[ 17.075432] PHL: [RXBUF][dev_id:1][ch:1] rxbd_num:64 buf_len:512
[ 17.081492] PHL: [RXBUF][dev_id:1][ch:0] rx_buf: num=768 size=4096
[ 17.089532] PHL: CH[0] Alloc 4096B RX buffer, got available size 7808B
[ 17.095898] PHL: [RXBUF][dev_id:1][ch:1] rx_buf: num=128 size=192
[ 17.102290] PHL: CH[1] Alloc 192B RX buffer, got available size 640B
[ 17.111633] PHL: RP agg is 121 for 640.
[ 17.115553] PHL: hal_cfg_fw_8192xb : fw_en 1.
[ 17.125623] PHL: [MAC] efuse_fv = 0xff
[ 17.129208] PHL: [MAC] [MAC-INFO]- CV : 1
[ 17.133192] PHL: [MAC] [MAC-INFO]- FV : 0
[ 17.139511] PHL: [MAC] efuse_aid = 0xffff
[ 17.143347] PHL: [MAC] [MAC-INFO]- AID : 6816
[ 17.152207] PHL: [MAC] Clear all bd index done.
[ 17.156640] PHL: [MAC] [FWDL] FW INIT......................................START
[ 17.163952] PHL: [MAC] Downloading Chip Halmac ID: 0x03
[ 17.169157] PHL: [MAC] [FWDL] Query Internal FW Chip_ID = 0x3
[ 17.174878] PHL: [MAC] [FWDL] Query Internal FW CV = 0x1
[ 17.180180] PHL: [MAC] [FWDL] Query Internal FW cat = 0x2
[ 17.185573] PHL: [MAC] [FWDL] WCPU OFF......................................DONE
[ 17.192939] PHL: [MAC] [FWDL] WCPU FWDL Boot.
[ 17.197309] PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
[ 17.202403] PHL: [MAC] [FWDL] WCPU FW BIN CHECK.............................DONE
[ 17.209787] PHL: [MAC] [FWDL] WCPU PRE BOOT..................................DONE
[ 17.217280] PHL: [MAC] [FWDL] WCPU IMAGE HEADER SEND........................DONE
[ 17.224625] PHL: [MAC] [FWDL] SEC_0:Len=0x5BD88,Addr=0x20100000,Type=0x2
[ 17.232511] PHL: [MAC] [FWDL] SEC_1:Len=0x1CE8,Addr=0x2015BD88,Type=0x7
[ 17.239087] PHL: [MAC] [FWDL] SEC_2:Len=0x4530,Addr=0x2021B000,Type=0x1
[ 17.245610] PHL: [MAC] [FWDL] SEC_3:Len=0x3C0,Addr=0x20237C00,Type=0x9
[ 17.252115] PHL: [MAC] [FWDL] DLFW DONE (0x8)
[ 17.281742] PHL: [MAC] [FWDL] INIT SYSMIB ENTRY (0xA)
[ 17.286621] PHL: [MAC] [FWDL] WCPU RAM PATCH.................................DONE
[ 17.294092] PHL: [MAC] _____ _____ _ ___ _ ___ ___
[ 17.300167] PHL: [MAC] | __\ \ / / \| | | _ \/_\ / __/ __|
[ 17.306323] PHL: [MAC] | _| \ \/\/ /| |) | |__ | _/ _ \\__ \__ \
[ 17.312492] PHL: [MAC] |_| \_/\_/ |___/|____| |_|/_/ \_\___/___/
[ 17.318664] PHL: [MAC] [FWDL] OS START DONE (0x26)
[ 17.323436] PHL: [MAC] [FWDL] WCPU FREERTOS INIT.............................DONE
[ 17.330899] PHL: [MAC] ___ _____ ___ ___ ___ ___ ___ _____
[ 17.337050] PHL: [MAC] | _ |_ _/ _ \/ __| | _ )/ _ \ / _ |_ _|
[ 17.343308] PHL: [MAC] | / | || (_) \__ \ | _ | (_) | (_) || |
[ 17.349383] PHL: [MAC] |_|_\ |_| \___/|___/ |___/\___/ \___/ |_|
[ 17.355454] PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
[ 17.360584] PHL: [MAC] [FWDL] FW INIT.......................................DONE
[ 17.370203] RTW: [HW-CAP] ic_name:rtl8192xb
[ 17.374218] RTW: [HW-CAP] macid_num:128
[ 17.378036] RTW: [HW-CAP] sec_cap:0x01
[ 17.381799] RTW: [HW-CAP] sec_cam_ent_num:0
[ 17.385935] RTW: [HW-CAP] rfpath_num_2g:2
[ 17.389946] RTW: [HW-CAP] rfpath_num_5g:2
[ 17.393921] RTW: [HW-CAP] rf_reg_path_num:2
[ 17.398087] RTW: [HW-CAP] max_tx_cnt:2
[ 17.401827] RTW: [HW-CAP] tx_nss_num:2
[ 17.405552] RTW: [HW-CAP] rx_nss_num:2
[ 17.409299] RTW: [HW-CAP] band_cap:2G
3 wait modprobe w[ 17.413017] RTW: [HW-CAP] bw_cap:20M 40M
ifi6 module ok![ 17.418492] RTW: [HW-CAP] proto_cap:b g n ac ax
[ 17.424387] RTW: [HW-CAP] wl_func:P2P MIRACAST TDLS
[ 17.429529] RTW: 0001:01:00.0: initialize #2 handler "netif RX" T@0/2
[ 17.435998] load default 2g thermal parameters
[ 17.440964] eric-tx CALL alloc_txring !!!!
[ 17.447127] swq tasklet init padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.454150] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.459776] RTW: ERROR rtw_hw_get_mac_addr failed
[ 17.464431] RTW: ERROR invalid mac addr:00:00:00:00:00:00, assign random MAC
[ 17.471483] RTW: Creating #5 virtual interface(s).
[ 17.476430] eric-tx CALL alloc_txring !!!!
[ 17.480402] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.486182] eric-tx CALL alloc_txring !!!!
[ 17.490146] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.495919] eric-tx CALL alloc_txring !!!!
[ 17.499880] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.505656] eric-tx CALL alloc_txring !!!!
[ 17.509630] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.515393] eric-tx CALL alloc_txring !!!!
[ 17.519359] padapter=(____ptrval____) dvobj=(____ptrval____)
[ 17.525067] RTW: rtw_cfg80211_init_ht_capab: band_type=0x1 dev_id=0x1 ht_cap->cap=1062
[ 17.532891] RTW: [rtw_build_he_supp_mcs] info_len:4
[ 17.537726] RTW: [rtw_build_he_supp_mcs] info_len:4
[ 17.542979] RTW: rtw_ndev_init(wlan1) if1 mac_addr=02:00:00:00:00:02
[ 17.550780] reg_therctl_ops(): reg wlan1 as idx 1
[ 17.555344] RTW: RTL WFO IPC (11) created
[ 17.559831] RTW: module init ret=0
[ 17.723741] >>PE functions run on pe cpu:
[ 17.723741]
[ 17.729116] [WIFI_TX_AMSDU] runs on PE1
[ 17.732885] [HTTP/IPERF] is disabled
recv err ret -28 [ 17.736443] [CRYPTO] is disabled
Unknown error -28[ 17.741140] [WFO] runs on PE0
[ 17.745557] [SRv6] is disabled
[ 17.748863] [PKT QUEUE] is disabled
[ 17.752328] [PKT TC QUEUE 0] is disabled
[ 17.756233] [PKT TC QUEUE 1] is disabled
[ 17.760146] [TR471] is disabled
[1;37;45m[PE] PE0 runs WFO function [0m
fw-size: 128832
Vboot
cpu_id: 0
fw: 3000000,80000,1f740
bl: 3020000
Load to DRAM...Copy 128832 bytes to DRAM, expected 128832
done
Booting...CPU0 changed to assert
CPU0 changed to deassert
Succeed
[ 17.816977] RTW: RTL WFO v1.1.2 (sha1 62033437) session 12 cpu_id 1 role 0x1
[ 17.821729] >>PE functions run on pe cpu:
[ 17.821729]
[ 17.824465] RTW: PI rw_ptr 0x902071e8 addr 0x90207200 pe_priv 0x902009b4 sw_seq 0x00000000
[ 17.829927] [WIFI_TX_AMSDU] runs on PE1
[ 17.841981] [HTTP/IPERF] is disabled
[ 17.845530] [CRYPTO] is disabled
[ 17.848748] [WFO] runs on PE1
[ 17.851693] [SRv6] is disabled
[ 17.854731] [PKT QUEUE] is disabled
[ 17.858209] [PKT TC QUEUE 0] is disabled
[ 17.862108] [PKT TC QUEUE 1] is disabled
[ 17.866014] [TR471] is disabled
[1;37;45m[PE] PE1 runs WFO function [0m
fw-size: 128832
Vboot
cpu_id: 1
fw: 3100000,80000,1f740
bl: 3120000
Load to DRAM...Copy 128832 bytes to DRAM, expected 128832
done
Booting...CPU1 changed to assert
CPU1 changed to deassert
Succeed
[ 17.909802] >>PE functions run on pe cpu:
[ 17.909802]
[ 17.910008] RTW: RTL WFO v1.1.2 (sha1 62033437) session 12 cpu_id 2 role 0x1
[ 17.915899] [WIFI_TX_AMSDU] runs on PE1
[ 17.922956] RTW: PI rw_ptr 0x908071e8 addr 0x90807200 pe_priv 0x908009b4 sw_seq 0x00000000
[ 17.935002] [HTTP/IPERF] is disabled
[ 17.938559] [CRYPTO] is disabled
[ 17.941764] [WFO] runs on PE2
[ 17.944715] [SRv6] is disabled
[ 17.947753] [PKT QUEUE] is disabled
[ 17.951231] [PKT TC QUEUE 0] is disabled
[ 17.955131] [PKT TC QUEUE 1] is disabled
[ 17.959043] [TR471] is disabled
[1;37;45m[PE] PE2 runs WFO function [0m
fw-size: 151780
Vboot
cpu_id: 2
fw: 3200000,80000,250e4
bl: 3230000
Load to DRAM...Copy 151780 bytes to DRAM, expected 151780
done
Booting...CPU2 changed to assert
CPU2 changed to deassert
Succeed
[ 18.137678] RTW: RTL WFO v1.1.2 (sha1 62033437) session 12 cpu_id 3 role 0x6
[ 18.144564] RTW: PI rw_ptr 0x900d4c00 addr 0x900d4c0c pe_priv 0x900d08f0 sw_seq 0x900d5e1c
4 wait modprobe wifi6 module ok!
[ 18.452061] rtl8221b: rtk_rtl8221b_moudle_init
[ 18.456358] elnath_pmx_request_gpio: pin:14 reg_off:0x0 bit_off:14
[ 18.762640] rtl8221b: Phys init. will be done by extGphy
[ 18.767802] rtl8221b: Creat 3 proc entry.
[ 18.813343] extGphy: RTK External GPHY Module Init.
[ 18.818687] extGphy: rtk_ext_gphy_probe with .dts
[ 18.823225] extGphy: Number of Port/GPHY Mapping (.dts) = 1
[ 18.829078] [1;33;41mextGphy: Can NOT read PHY ID from phyAddr: 7 [rtk_ext_gphy_auto_detect(line 1356)][m
[ 18.838697] extGphy: External GPHY List:
[ 18.842557] extGphy: #0 node (ffffff800da7c480): [Port 6] [phyAddr 7] [ST C45] [NO Driver]
[ 18.850817] extGphy: Total in the list: 1
[ 18.854792] [1;33;41mextGphy: !!!No driver support for PHY at addr 7 [rtk_ext_gphy_all_init(line 1553)][m
[ 18.864805] extGphy: Register a miscellaneous device [/dev/extGphy]:
[ 18.871055] extGphy: Creat proc entry.
[ 18.874722] rtk_ext_gphy_mapper_init-2664
[ 18.980382] Allocate upload SKB cache, max_buf_len 10752(10240)
[ 18.986151] insert here, priority: 9, portmask 268435455, rx: (____ptrval____)
[ 19.182422] ntfs3: Max link count 4000
sh: factory: unknown operand
[ 19.255596] UBIFS (ubi0:9): Mounting in unauthenticated mode
[ 19.261473] UBIFS (ubi0:9): background thread "ubifs_bgt0_9" started, PID 1674
[ 19.322694] UBIFS (ubi0:9): recovery needed
[ 19.468626] UBIFS (ubi0:9): recovery completed
[ 19.472973] UBIFS (ubi0:9): UBIFS: mounted UBI device 0, volume 9, name "ubi_apps"
[ 19.480474] UBIFS (ubi0:9): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 19.490370] UBIFS (ubi0:9): FS size: 103485440 bytes (98 MiB, 815 LEBs), journal size 5206016 bytes (4 MiB, 41 LEBs)
[ 19.500942] UBIFS (ubi0:9): reserved for root: 4887873 bytes (4773 KiB)
[ 19.507453] UBIFS (ubi0:9): media format: w5/r0 (latest is w5/r0), UUID A41FABC0-1060-40C2-91FD-F615891116AB, small LPT model
Loading Realtek IGMP/ MLD Snooping Module...
[ 19.606732] ----------register snooping hook function ---------
[ 19.612524] ---------fc get snooping hook fucntion-------
[ 19.617871] multicast_moudle_init
----- do_rc [/etc/init.d/rc4] -----
----- do_rc [/etc/init.d/rc6] -----
----- do_rc [/etc/init.d/rc10] -----
----- do_rc [/etc/init.d/rc14] -----
----- do_rc [/etc/init.d/rc18] -----
----- do_rc [/etc/init.d/rc19] -----
mount: mounting none on /proc/bus/usb failed: No such file or directory
smuxdev: loaded
----- do_rc [/etc/init.d/rc20] -----
random: fast init done
mnet built on 2026.09.18-02:50+0000
----- do_rc [/etc/init.d/rc22] -----
Start rtk_ramonitor daemon!
[setup_usock_thread:9652] Create new theread for usock
[1;35m[MESH][setup_multi_ap_auto_thread:1257] Create multi_ap_role_election_func[0m
**********************************************
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "gpio-keys"
Supported events:
Event type 0 (Sync)
Event type 1 (Key)
Event code 238
Event code 408
Event code 529
Event type 20 (Repeat)
Grab succeeded, ungrabbing.
fscanf failed: getConfigPartitionCount 10506
Select 5G on wlan0
Check wlan Reset value to -1
cs mib...
Wlan0:5G
No need swap wlan cs mib!
Select 5G on wlan0
Check wlan hs mib...
Wlan0:TX_POWER_CCReset value to -1
K_A[0]:00, TX_POWER_5G_HT40_1S_A[35]:00
Wlan0:TX_POWER_TSSI_CCK_A[0]:00, TX_POWER_TSSI_5Reset value to -1
G_HT40_1S_A[35]:00
Wlan HW no calibration !No need to swap hs mib
Wlan HW no calibratioReset value to -1
n or Calibration value error, please Calibrate again!
**********************************************
sh: Reset value to -1
/etc/scripts/setupclock.sh: not found
2
Testing ... (interrupt to exit)
set WLAN_MBSSIReset value to -1
B_TBL.0.is_ax_support=1
Reset value to -1
Reset value to -1
Reset value to -1
Reset value to -1
Reset value to -1
Reset value to -1
set WLAN1_MBSSIB_TBL.0.is_ax_support=1
Set svlan tpid ptn = 0x8100 to stag[0]
----- do_rc [/etcSet svlan tpid ptn = 0x88a8 to stag[1]
/init.d/rc32] -----
0
WLAN0 Dispatch mode: 1, cpu: 0
WLAN0 Dispatch mode: 0, cpu: 0
WLAN1 Dispatch mode: 0, cpu: 0
----- do_rc [/etc/init.d/rc35] -----
run rcm voip script...
[HWNAT] rtk_9607f_flow_init: ##### hash fib bits width: flow(type-0) act_mask 0x140000 (224 bits), type-1 act_mask 0x0 (0 bits), default act_mask 0x4d0000 (90 bits) @rtk_9607f_flow_init(5522)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 0 (RTK_9607F_FLOW_PROFILE_FLOW_5TUPLE), profile 0 hash_mask_idx = 0 @rtk_9607f_flow_hash_profile_init(5200)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 1 (RTK_9607F_FLOW_PROFILE_FLOW_2TUPLE), profile 0 hash_mask_idx = 1 @rtk_9607f_flow_hash_profile_init(5243)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 2 (RTK_9607F_FLOW_PROFILE_FLOW_MC), profile 0 hash_mask_idx = 2 @rtk_9607f_flow_hash_profile_init(5264)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 2 (RTK_9607F_FLOW_PROFILE_FLOW_MC), profile 1 hash_mask_idx = 3 @rtk_9607f_flow_hash_profile_init(5305)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 3 (RTK_9607F_FLOW_PROFILE_DEFAULT_DROP), profile 0 hash_mask_idx = 4 @rtk_9607f_flow_hash_profile_init(5373)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 4 (RTK_9607F_FLOW_PROFILE_MC_WIFI_TX_AMSDU_OFLD), profile 0 hash_mask_idx = 5 @rtk_9607f_flow_hash_profile_init(5391)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 5 (RTK_9607F_FLOW_PROFILE_DUALFRAG_OR_ESP), profile 0 hash_mask_idx = 6 @rtk_9607f_flow_hash_profile_init(5411)
[HWNAT] rtk_9607f_flow_hash_profile_init: ##### init hash profile 5 (RTK_9607F_FLOW_PROFILE_DUALFRAG_OR_ESP), profile 1 hash_mask_idx = 7 @rtk_9607f_flow_hash_profile_init(5457)
bridge_5tuple_flow_accelerate_by_2tuple (UC):0
mc_5tuple_flow_accelerate_by_2tuple(MC):0
bit mask = 0x8, action = drop
echo gpio-led0 > /sys/class/leds/LED_PPP_G/trigger
crond[1776]: crond: crond (busybox 1.22.1) started, log level 8
[mib_init_mib_with_program_default:1966] Load from program default (type=8, action=2, range=2)!
[_load_xml_file:763] load from /etc/config_default.xml (tmp_file=/tmp/cnf
bit mask = 0x8, action = forward
tmp_M6RszZ, dtype=8)
[_load_xml_file:763] load from /var/config/config.xml (tmp_file=/tmp/cnftmp_SpKP41, dtype=8)
ponmode
port 3
assign to nas0
mapping root DEV=eth0 virtual DEV=nas0 to port 3
mapping root DEV=eth1 virtual DEV=nas0 to port 3
Set auto_reserve_vlan to 1 OK.
Turn on phy power...
MIB chain descriptors checking (total 119) ok !
/bin/sh: can't open '/etc/scripts/rps.sh'
diable printk= 0 parameter is 0
sh (1819): drop_caches: 3
Starting server at https://localhost:7443/ and http://localhost:7080/
rt_ponmisc init
RTK.0> command:rt_ponmisc ca-pon: load PON_VOQ_MODE: 0
set mode 4 speed __pon_eth_init(): init start
0
ca-pon: init PON_RX_LOS_POLARITY_INVERT as 0.
loading serders file: /etc/serdes/pon_serdes_activee_100m_B.txt , mode=12, rev=66
loading serders file: /etc/serdes/pon_serdes_activee_100m.txt , mode=12
[check_sw_version 48229] latest_version[V4.0.18_260920]
------- 8277(B) VM Turning ----------------
[check_sw_version 48243] recode version[V4.0.18_260220]
same version, latest[V4.0.18_260920][V4.0.18] recoca-pon: load PON SerDes configuration from SerDes file successfully
rd[V4.0.18_260220][V4.0.18]
serial 4c2efe000000, macStr 4c2efe000000
ca-pon: init PON SerDes OK
ca-pon: init PDC OK
set Dying Gasp Registers
killall: inetd: no process killed
>>> Disable /dev/console XON XOFF !!!
/bin/slogd -n -s 51200 -l 5 ...
starting pid 1860, tty '/dev/ttyS0': '/bin/login -p'
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+5 = 3f
login: ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
sh: can't create /sys/class/leds/LED_8221B_P0_0/brightness: nonexistent directory
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+5 = 3f
__pon_eth_init: init active-Ethernet successfully
aal_pon_mac_max_frame_size_set:759, invaild MTU size [12288 / 12288]
ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=7
ca-pon: init OK.
RTK.0> command:setupUniPortCapability:1245 line is 2;2;2;0;0;0;3
sh: can't create /sys/class/leds/LED_EPHY4/trigger: nonexistent directory
setupUniPortCapability:1273 pch is 2, port 0, UNI_PORT_GE
setupUniPortCapability:1273 pch is 2, port 1, UNI_PORT_GE
setupUniPortCapability:1273 pch is 2, port 2, UNI_PORT_GE
setupUniPortCapabil[1;33;41mextGphy: !!!No driver support for PHY at addr 7 [rtk_ext_gphyAutoNegoAbility_get(line 2151)][m
ity:1257 pch is 0[1;33;41mextGphy: !!!No driver support for PHY at addr 7 [rtk_ext_gphyAutoNegoAbility_set(line 2123)][m
, port 3, UNI_PORT_NONE
[setPortNegoCapability] Cannot get ability of the port 4 !!, ret = 3
setupUniPortCapability:1257 pch is 0, port 4, UNI_PORT_NONE
[setPortNegoCapability] Cannot get ability of the port 5 !!, ret = 3
setupUniPortCapability:1257 pch is 0, port 5, UNI_PORT_NONE
setupUniPortCapability:1278 To-Do: not suuport UNI_PORT_2P5GE yet
sh: can't create /sys/class/leds/LED_USB1/trigger: nonexistent directory
/bin/sh: can't create /sys/class/leds/Lport 2
ED_USB1/device_naassign to eth0.2
me: nonexistent dmapping root DEV=eth0 virtual DEV=eth0.2 to port 2
irectory
sh: canmapping root DEV=eth1 virtual DEV=eth0.2 to port 2
't create /sys/class/leds/LED_VPN/trigger: nonexistent directory
ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
br0: port 1(eth0.2.0) entered blocking state
br0: port 1(eth0.2.0) entered disabled state
eth0.2 opened
[1;33;46m<subr_net.c 21372 setup_port_path_cost_for_bridge> [mtmp_cmd = echo 10 > /sys/class/net/eth0.2.0/brport/path_cost
[restart_ethernet@18456] eth0.2.0 is up
getUniPortCapability:1346 line is 2;2;2;0;0;0;3
getUniPortCapability:1354 pch is 2, port is 2
port 1
assign to eth0.3
mapping root DEV=eth0 virtual DEV=eth0.3 to port 1
mapping root DEV=eth1 virtual DEV=eth0.3 to port 1
ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
echo gpio-led0 > ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
/sys/class/leds/LED_PPP_G/trigger
br0: port 2(eth0.3.0) entered blocking state
br0: port 2(eth0.3.0) entered disabled state
sh: can't create /procdevice eth0.3.0 entered promiscuous mode
/internet_flag: ndevice eth0.2.0 entered promiscuous mode
onexistent directory
eth0.3 opened
[1;33;46m<subr_net.c 21372 setup_port_path_cost_for_bridge> [mtmp_cmd = echo 10 > /sys/class/net/eth0.3.0/brport/path_cost
[restart_ethernet@18456] eth0.3.0 is up
getUniPortCapability:1346 line is 2;2;2;0;0;0;3
getUniPortCapability:1354 pch is 2, port is 1
sh: can't open '/etc/scripts/rps.sh'
port 0
assign to eth0.4
mapping root DEV=eth0 virtual DEV=eth0.4 to port 0
mapping root DEV=eth1 virtual DEV=eth0.4 to port 0
connect is failure
[set_lanhost_linkchange_port_status 25249]: failed! portIdx=2
connect is failure
[set_lanhost_linkchange_port_status 25249]: failedca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
! portIdx=1
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
Disable led_test
br0: port 3(eth0.4.0) entered blocking state
br0: port 3(eth0.4.0) entered disabled state
device eth0.4.0 entered promiscuous mode
eth0.4 opened
[1;33;46m<subr_net.c 21372 setup_port_path_cost_for_bridge> [mtmp_cmd = echo 10 > /sys/class/net/eth0.4.0/brport/path_cost
[restart_ethernet@18456] eth0.4.0 is up
getUniPortCapability:1346 line is 2;2;2;0;0;0;3
getUniPortCapability:1354 pch is 2, port is 0
[rtk_fc_stp_clean@4437]: ERROR! No such file or directory
[rtk_fc_stp_clean@4449]: ERROR! No such file or directory
connect is failure
[set_lanhost_linkchange_port_status 25249]: failed! portIdx=0
/bin/sh /etc/scripts/mpctl_led_label_trigger.sh LED_PPP_Gdelete client entry of dev eth0.2.0 ---
delete client entry of dev eth0.3.0 ---
delete client entry of dev eth0.4.0 ---
Auto Link-Local Address for br0
checkDefaultSSID 46418 tmpBuf=7PZL
checkDefaultSSID 46418 tmpBuf=7PZL
[1;35m[MESH]set mesh role to controller, gOrigMeshController=0[0m
mode=0 , rtk_op_mode = 0
[1;35m[MESH]set mesh role to controller, gOrigMeshController=1[0m
(wlan0)[hs]wlan0_5g:1, [cs]select 5g on wlan0, read hwmib from HW_WLAN0
wlan0 flash_set:xcap=88
wlan0 flash_set:rfe=255
wlan0 flash_set:thermalA=30
wlan0 flash_set:thermalB=31
wlan0 flash_set:thermalC=255
wlan0 flash_set:thermalD=255
RTW: rtw_load_phy_file_path(0) Parameter path: "/etc/conf/rtl8852ce/RFE53/"
wlan0 flash_set:para_path=/etc/conf/
wlan0 flash_set:2G_cck_tssi_A=010100f8f8f8
wlan0 flash_set:2G_cck_tssi_B=fffffefdfdfd
RTNETLINK answers: File exists
[1;33;46m<subr_net.c 16762 set_ipv4_lan_policy_route> [mSet IPv4 LAN route for ifname (br0), table(260)
iptables: Bad rule (does a matching rule exist in that chain?).
do_restart_dnsrelay:5379 no delay dns
killall: ther_control: no process killed
wlan0 flash_set:2G_cck_tssi_C=000000000000
wlan0 flash_set:2G_cck_tssi_D=000000000000
wlan0 flash_set:2G_bw40_1s_tssi_A=040402f8f8
wlan0 flash_set:2G_bw40_1s_tssi_B=0000fefcfc
wlan0 flash_set:2G_bw40_1s_tssi_C=0000000000
wlan0 flash_set:2G_bw40_1s_tssi_D=0000000000
Parsed Chip Mode Value: 0x3281
MCM board
-----------------------------------------------------------------------------------
Start Thermal Control
-----------------------------------------------------------------------------------
wlan0: ther_max=57, ther_hi=54, ther_low=51 (funcoff=1 limit=1 fwduty=0 txpath=0 power=0)
wlan1: ther_max=54, ther_hi=50, ther_low=47 (funcoff=1 limit=1 fwduty=0 txpath=0 power=0)
-----------------------------------------------------------------------------------
wlan0: Disable Tx Duty Cycle (ther_avg:0, state:init)
wlan1: Disable Tx Duty Cycle (ther_avg:0, state:init)
wlan0 flash_set:5G_bw40_1s_tssi_A=14131410140f0c1410080c10090a
wlan0 flash_set:5G_bw40_1s_tssi_B=211d1614161a191c1a151417140f
wlan0 flash_set:5G_bw40_1s_tssi_C=0000000000000000000000000000
wlan0 flash_set:5G_bw40_1s_tssi_D=0000000000000000000000000000
wlan0 flash_set:2G_rx_gain_cck=18
wlan0 flash_set:2G_rx_gain_ofdm=18
wlan0 flash_set:5G_rx_gain_low=206
wlan0 flash_set:5G_rx_gain_mid=204
wlan0 flash_set:5G_rx_gain_high=204
wlan0 flash_set:chan_plan=127
(wlan1)[hs]wlan0_5g:1, [cs]select 5g on wlan0, read hwmib from HW_WLAN1
wlan1 flash_set:xcap=255
wlan1 flash_set:rfe=255
wlan1 flash_set:thermalA=27
wlan1 flash_set:thermalB=27
wlan1 flashRTW: rtw_load_phy_file_path(1) Parameter path: "/etc/conf/rtl8192xbe/RFE50/"
_set:thermalC=255
iptables v1.4.18: Couldn't load target `no_internet_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
wlan1 flash_set:thermalD=255
iptables v1.4.18: Couldn't br0: port 4(eth0.2.46) entered blocking state
load target `no_ibr0: port 4(eth0.2.46) entered disabled state
nternet_redirect'device eth0.2.46 entered promiscuous mode
:No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
wlan1 flash_set:para_path=/etc/conf/
iptables: No chain/target/match by that name.
wlan1 flash_set:2G_cck_tssi_A=010100f8f8f8
wlan1 flash_set:2G_cck_tssi_B=fffffefdfdfd
wlan1 flash_set:2G_cck_tssi_C=000000000000
wlan1 flash_set:2G_cck_tssi_D=000000000000
wlan1 flash_set:2G_bw40_1s_tssi_A=040402f8f8
wlan1 flash_set:2G_bw40_1s_tssi_B=0000fefcfc
[update_monitor_list_file:26760] process_name = dnsmasq, action = 0
Open file /var/tmp/hosts failed !
wlan1 flash_set:2G_bw40_1s_tssi_C=0000000000
wlan1 flash_set:2G_bw40_1s_tssi_D=0000000000
wlan1 flash_set:5G_bw40_1s_tssi_A=14131410140f0c1410080c10090a
wlan1 flash_set:5G_bw40_1s_tssi_B=211d1614161a191c1a151417140f
wlan1 flash_set:5G_bw40_1s_tssi_C=0000000000000000000000000000
wlan1 flash_set:5G_bw40_1s_tssi_D=0000000000000000000000000000
wlan1 flash_set:2G_rx_gain_cck=18
wlan1 flash_set:2G_rx_gain_ofdm=18
wlan1 flash_set:5G_rx_gain_low=206
wlan1 flash_set:5G_rx_gain_mid=204
wlan1 flash_set:5G_rx_gain_high=204
wlan1 flash_set:chan_plan=127
br0: port 5(eth0.3.46) entered blocking state
br0: port 5(eth0.3.46) entered disabled state
device eth0.3.46 entered promiscuous mode
[start_wifi_priv_cfg 801] 0 wlanDisabled=0
[start_wiRTW: ERROR update_mgntframe_attrib bmc_sta=NULL
fi_priv_cfg 818]&RTW: [TXSC] clear txsc entry
launch: wlan_idxRTW: [core_mib_txforce][txforce] macid:0, fix_rate = 0xffff
= 0
RTW: [TXSC] clear txsc entry
RTW: [TXSC] clear txsc entry
RTW: [TXSC] clear txsc entry
[update_monitor_lRTW: ERROR [core_mib_edcca_mode] should be config after iface up
ist_file:26760] process_name = dnsmRTW: core_mib_power_percent(1534), interface is not running
asq, action = 1
random: dnsmasq: uninitialized urandom read (128 bytes read)
[0] wlanDisabled=RTW: core_mib_power_ref(1558), interface is not running
0
gen_hapd_cfg RTW: core_mib_power_limit(1584), interface is not running
[get_wifi_conf][645][if_idx = 0] [index = 0]++
config->encrypt=4 psk_enable=2 authtype=2 encmode=2 psk_format=0 gk_rekey=86400
enEzpwAvSN3S
wpa_cipher=0x0 wpa2_cipher=0x2 enable_1x=0
dot11IEEE80211W=1 enableSHA256=0
sae_pwe=0
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+7 = 41
[get_wifi_vif_conf][70], if_idx=0 index=1
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+7 = 41
VAP0: psk_enable=10 authtype=2 encmode=2 psk_format=0 gk_rekey=86400
VAP0: Z{[O)K42{:WIf6ykYI)v*#145?Aq^X
VAP0: wpa_cipher=0x0 wpa2_cipher=0x2 enable_1x=0
VAP0: dot11IEEE80211W=1 enableSHA256=0
VAP0:random: dnsmasq: uninitialized urandom read (48 bytes read)
sae_pwe=2
[get_wifi_vif_conf][70], if_idx=0 index=2
[get_wifi_vif_conf][70], if_idx=0 index=3
[get_wifi_vif_conf][70], if_idx=0 index=4
Generating VAP1 "wlan0-vap0" configuration
wlan0 VAP2 disabled
wlan0 VAP3 disabled
wlan0 VAP4 disabled
launch hapd: wlan_idx = 0
launch_hapd_by_cmd(7128) echo 1 into wlan0 coex_2g_40m
sh: can't create /proc/net/rtk_wifi6/wlan0/coex_2g_40m: nonexistent directory
random: hostapd: uninitialized urandom read (4096 bytes read)
delete client entry of dev eth0.2.46 ---
delete client entry of dev eth0.3.46 ---
rfkill: Cannot openRTW: [rtw_hw_start 882] Start flash process !!
RFKILL control dPHL: RP agg is 121 for 640.
evice
PHL: hal_cfg_fw_8852c : fw_en 1.
PHL: [MAC] [ERR]Access efuse in suspend
PHL: [MAC] efuse_fv = 0xff
PHL: [MAC] [MAC-INFO]- CV : 1
PHL: [MAC] [MAC-INFO]- FV : 1
PHL: [MAC] efuse_aid = 0xffff
PHL: [MAC] [MAC-INFO]- AID : 6758
PHL: [MAC] Clear all bd index done.
PHL: [MAC] [FWDL] FW INIT......................................START
PHL: [MAC] Downloading Chip Halmac ID: 0x02
PHL: [MAC] [FWDL] Query Internal FW Chip_ID = 0x2
PHL: [MAC] [FWDL] Query Internal FW CV = 0x1
PHL: [MAC] [FWDL] Query Internal FW cat = 0x2
PHL: [MAC] [FWDL] WCPU OFF......................................DONE
PHL: [MAC] [FWDL] WCPU FWDL Boot.
PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
PHL: [MAC] [FWDL] WCPU FW BIN CHECK.............................DONE
PHL: [MAC] [FWDL] WCPU PRE BOOT..................................DONE
PHL: [MAC] [FWDL] WCPU IMAGE HEADER SEND........................DONE
PHL: [MAC] [FWDL] SEC_0:Len=0x5F798,Addr=0x20100000,Type=0x2
PHL: [MAC] [FWDL] SEC_1:Len=0x1AF0,Addr=0x2015F798,Type=0x7
PHL: [MAC] [FWDL] SEC_2:Len=0x5CE0,Addr=0x2021B000,Type=0x1
PHL: [MAC] [FWDL] SEC_3:Len=0x3C0,Addr=0x20237C00,Type=0x9
PHL: [MAC] [FWDL] DLFW DONE (0x8)
PHL: [MAC] [FWDL] INIT SYSMIB ENTRY (0xA)
PHL: [MAC] [FWDL] WCPU RAM PATCH.................................DONE
PHL: [MAC] _____ _____ _ ___ _ ___ ___
PHL: [MAC] | __\ \ / / \| | | _ \/_\ / __/ __|
PHL: [MAC] | _| \ \/\/ /| |) | |__ | _/ _ \\__ \__ \
PHL: [MAC] |_| \_/\_/ |___/|____| |_|/_/ \_\___/___/
PHL: [MAC] [FWDL] OS START DONE (0x26)
PHL: [MAC] [FWDL] WCPU FREERTOS INIT.............................DONE
PHL: [MAC] ___ _____ ___ ___ ___ ___ ___ _____
PHL: [MAC] | _ |_ _/ _ \/ __| | _ )/ _ \ / _ |_ _|
PHL: [MAC] | / | || (_) \__ \ | _ | (_) | (_) || |
PHL: [MAC] |_|_\ |_| \___/|___/ |___/\___/ \___/ |_|
PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
PHL: [MAC] [FWDL] FW INIT.......................................DONE
PHL: hal_mac_print_fw_version: FW version V0.27.112.5, Ready
PHL: ERROR _hal_mac_get_ofld_cap : disable fw ofld cmd!
PHL: Set RX packet size filter to 12288B
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/PHY_REG.txt" (2867/27448) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/PHY_REG_GAIN.txt" (801/12047) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/RadioA.txt" (4113/34436) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/RadioB.txt" (4057/33902) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/TXPWR_ByRate.txt" (136/3502) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/TXPWR_TrackTSSI.txt" (671/4326) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/TXPWR_LMT.txt" (5320/33680) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/PHY_REG.txt" (113/3067) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/PHY_REG_GAIN.txt" (481/6692) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/RadioA.txt" (1161/8267) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/RadioB.txt" (1161/8231) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/TXPWR_ByRate.txt" (136/3348) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/TXPWR_TrackTSSI.txt" (671/3945) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8852ce/RFE53/FX7555D_PON/TXPWR_LMT.txt" (3040/22285) OK.
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x0
PHL: rtw_hal_mac_fw_log_cfg: level 4, output 0x00000000, comp 0x00000000, comp ext 0x00000000.
PHL: rtw_hal_mac_fw_log_cfg: level 4, output 0x00000002, comp 0x00000000, comp ext 0x00000000.
PHL: rtw_hal_mac_fw_log_cfg: level 4, output 0x00000002, comp 0x00000004, comp ext 0x00000000.
PHL: rtw_hal_start: Get MAC(0xd200) ok!!! 0x00000000
PHL: Set regular_idx:2 (REGULATION_FCC)
PHL: Set MAC(0xd200) ok!!! 0x00000000
RTW: rtw_update_sw_cap : sw_role_cap->bf_cap 204
PHL: Config role #0 of type 2. MBSSID: 0.
PHL: Initializing port 0 with 0 M-BSSID.
RTW: [PHL STA]- role-idx: 0
RTW: [PHL STA]- mac_addr:02:00:00:00:00:41
RTW: [PHL STA]- aid: 0
RTW: [PHL STA]- macid: 0
RTW: [PHL STA]- wifi_band: 0
RTW: [PHL STA]- bw: 0
RTW: [PHL STA]- chan: 0
RTW: [PHL STA]- offset: 0
RTW: [rtw_hw_iface_init] enable interrupt in the END of init
mask: 0x25000000, 0x00180005, 0x00000000, 0x00600000, 0x00000002
RTW: [TXSC] clear txsc entry
[_netdev_open] change tx_mode form 0 to 0
RTW: change mode, old_mode=2, new_mode=4, fw_state=0x8
RTW: rtw_set_802_11_infrastructure_mode(wlan0)Start AP mode! (1)
RTW: [TXSC_INIT][wlan0] a4_enable:0, a4_sta_list/a4_gptr_tbl init.
RTW: [TXSC_INIT][wlan0] txsc:1, txsc_amsdu:1 amsdu_mode:1
RTW: [RXSC_INIT][wlan0] rxsc:1
_rtk_fc_wifi_event_handling_cb_register: cb func ffffffc009c191c8
RTW: pcie_phy_addr_start 0xa0400000 chip_id 3
RTW: [rtl_wfo_fc_callback_hook_update]: ifname=wlan0, up=1, client_mode=0, do_nat25=0
br0: port 6(eth0.4.46) entered blocking state
br0: port 6(eth0.4.46) entered disabled state
device eth0.4.46 entered promiscuous mode
br0: port 7(wlan0) entered blocking state
br0: port 7(wlan0) entered disabled state
device wlan0 entered promiscuous mode
wlan0: interface stRTW: [_rtw_sitesurvey_condition_check]Caller: cfg80211_rtw_scan on wlan0
ate UNINITIALIZEDRTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
->COUNTRY_UPDATE
RTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
ACS: Automatic cPHL: Set RX packet size filter to 12288B
hannel selection started, this may take a bit
iptables: No chain/target/match by that name.
wlan0: interface state COUNTRY_UPDATE->ACS
wlan0: ACS-STARTED
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+5 = 3f
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
set dos:0x4001ff
ERROR! No such file or directory
[rtk_fw_dos_set 3456] ret = -2
/bin/sh: can't create proc/igmp/ctrl/skbMarkExtraSwitchPortId: nonexistent directory
br0: port 4(eth0.2.46) entered disabled state
device eth0.2.46 left promiscuous mode
[1;33;46m<fc_apibr0: port 4(eth0.2.46) entered disabled state
.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `LAN_SYN_FLOOD_PROOF':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -s 192.168.1.0/24 -d 192.168.1.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -d 192.168.1.1 --dport 80 -j DROP
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -s 192.168.4.0/24 -d 192.168.4.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -d 192.168.4.1 --dpobr1: port 1(eth0.2.46) entered blocking state
rt 80 -j DROP
br1: port 1(eth0.2.46) entered disabled state
device eth0.2.46 entered promiscuous mode
br0: port 5(eth0.3.46) entered disabled state
device eth0.3.46 left promiscuous mode
br0: port 5(eth0.3.46) entered disabled state
br1: port 2(eth0.3.46) entered blocking state
br1: port 2(eth0.3.46) entered disabled state
device eth0.3.46 entered promiscuous mode
wlan0: Disable Tx Duty Cycle (ther_avg:5, state:init)
br0: port 6(eth0.4.46) entered disabled state
device eth0.4.46 left promiscuous mode
br0: port 6(eth0.4.46) entered disabled state
br1: port 3(eth0.4.46) entered blocking state
br1: port 3(eth0.4.46) entered disabled state
device eth0.4.46 entered promiscuous mode
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `interface_grouping_br0':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
[1;33;46m<subr_net.c 16762 set_ipv4_lan_policy_route> [mSet IPv4 LAN route for ifname (br0), table(260)
iptables v1.4.18: Couldn't load target `interface_grouping_br1':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
Chain 'ISOLATION_MAP' doesn't exist.
RTNETLINK answers: File exists
Auto Link-Local Address for br1
[setup_interface_grouping:21916] do_ipv6_iapd wanconn=65536, ifname=ppp0
cp: can't stat '/var/run/dhcpcV6.leases.ppp0': No such file or directory
[doDelegation:951] for lease file = /var/run/dhcpcV6.leases.ppp0
do_restartLanV6Server - 693
do_cleanLanV6Server - 807
interface wlan0.46 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
smuxctl failed(ret=-1) return errno(19) No such device
[setup_dhcpdv6_conf_with_single_br:818]
no prefix!! set tmp subnet conf
[1;33;46m<subr_net.c 34108 startWan> [mstartWan Start all WAN
ca_ni_set_mac_address: i=0, cep->port_cfg.port_id[i]=0
ca_ni_set_mac_address: i=1, cep->port_cfg.port_id[i]=1
ca_ni_set_mac_address: i=2, cep->port_cfg.port_id[i]=2
ca_ni_set_mac_address: i=3, cep->port_cfg.port_id[i]=3
ca_ni_set_mac_address: i=4, cep->port_cfg.port_id[i]=4
ca_ni_set_mac_address: i=5, cep->port_cfg.port_id[i]=6
nas0 opened
Create /var/ppp/peerandom: crng init done
rs/opts_ppp0 file OK!
==> [addEthWANdev] /bin/smuxctl --if nas0 --rx --tags 1 --filter-vid 0x23 1 --filter-unicast-mac 1 --rule-priority 900 --set-rxif nas0_0 --rule-alias nas0_0-rx-default-root --target ACCEPT --rule-append
==> [addEthWANdev] /bin/smuxctl --if nas0 --rx --tags 2 --filter-vid 0x23 1 --filter-unicast-mac 1 --rule-priority 900 --set-rxif nas0_0 --rule-alias nas0_0-rx-default-root --target ACCEPT --rule-append
==> [addEthWANdev] /bin/smuxctl --if nas0_0 --tx --tags 0 --push-tag --set-vid 0x23 1 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append
==> [addEthWANdev] /bin/smuxctl --if nas0_0 --tx --tags 1 --set-vid 0x23 1 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append
==> [addEthWANdev] /bin/smuxctl --if nas0_0 --tx --tags 2 --set-vid 0x23 2 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append
Prefix Mode is WANDelegated, now change to this WAN, 10000
[cfg_mib_update_ex:593] _mib_update(8) commitnow=1 (check_commit=1) success
[startConnection@31198] pEntry->ifIndex = 65536, pEntry->cmode = 2
PPPoE
Internet Systems Consortium DHCP Server 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Config file: /var/dhcpd6.conf
Database file: /var/dhcpd6.leases
PID file: /var/run/dhcpd6.pid
Wrote 0 NA, 0 TA, 0 PD leases to lease file.
No subnet6 declaration for br0 (no IPv6 addresses).
** Ignoring requests on br0. If this is not what
you want, please write a subnet6 declaration
in your dhcpd.conf file for the network segment
to which interface br0 is attached. **
Not configured to listen on any interfaces!
If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug. These pages explain the proper
process and the information we find helpful for debugging.
exiting.
[stop_upnp:23199] Stop miniupnpd! (wanIf=ppp0)
upnpctrl(sync): Get miniupnpd pid failed!
[start_upnp:23169] Start miniupnpd! (wanIf=ppp0)
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
[start_upnp:23169] Start miniupnpd! (wanIf=ppp0)
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
run /etc/rc_voip_module
0
0
PCM ISR SoC:0
CPU NR:2
bind PCM ISR to cpu 0
modify cortina_uart 24 to cpu 1
modify per_ictl 10 to cpu 1
Loading AIPC module /lib/modules/5.10.70/kernel/drivers/char/aipc/aipc_char.ko
Loading VOIP module /lib/modules/5.10.70/kernel/rtk_voip/voip_kernel.ko
wlan0: ACS-COMPLETED freq=5180 channel=36
skip ieee802RTW: wlan0 has no STA. Not issue BC deauth.
11n_check_40mhz
RTW: Beacon BSS MAC: 02:00:00:00:00:41
RTW: [rtw_build_he_supp_mcs] info_len:8
RTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
RTW: IE CH(36) BW(3) OF(1)
RTW: start_bss_network: Affffffc0121bd000, C(0) B(-1) O(-1)
RTW: update_wireless_mode(wlan0) chan=36, network_type=22, wireless_mode=22(3f)
ca77xx_audio_init
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x8
ca77xx_audio_probe: Enter
ca77xx_audio_probe: 2172, audio 0000000031420392
rtw_phl_ru_set_ch_bw:
ca-audio f7001b80.ssp0: ssp reg - [mem 0xf7001b80-0xf7001bff flags 0x200] mapped at 0x00000000ce303346
RTW: assoc success
ca-audio f7001b80.ssp0: ssp irq is 57
PHL: [MAC] mac_set_bcn_ignore_edcca: port(0), mbssid(0 ms), band(0), en/dis(1)
ca-audio f7001b80.ssp0: SSP HW ver 0x3c
RTW: [WFO]............................................STARTING
ext_clk 0
clk_enhance 1
divisor 12
pclk 4096
metadata 0x1
ca-audio f7001b80.ssp0: dma int tx reg - [mem 0xf7001e18-0xf7001e1f flags 0x200] mapped at 0x00000000a22f0738
iptables: Too many links.
ca-audio f7001b80.ssp0: dma int rx reg - [mem 0xf7001e28-0xf7001e2f flags 0x200] mapped at 0x000000006ae7f6bc
ca-audio f7001b80.ssp0: dma int ssp reg - [mem 0xf7001e38-0xf7001e3f flags 0x200] mapped at 0x00000000fb8e24a6
iptables: Too manyca-audio f7001b80.ssp0: dma glb reg - [mem 0xf7001064-0xf700106b flags 0x200] mapped at 0x000000006b91185a
links.ca-audio f7001b80.ssp0: dma ssp reg - [mem 0xf7001a80-0xf7001aff flags 0x200] mapped at 0x00000000c3a367ac
ca-audio f7001b80.ssp0: dma-tx irq is 55
ca-audio f7001b80.ssp0: dma-rx irq is 56
spi_linux_wrapper_init()
pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: pinmux group:spi_group reg_off:0x8 bit_off:0
SLIC module being probed
slic_spi_probe: slic_spi[ 0 ] = 00000000e55708c9
[1;33;46m<subr_ipvspi_linux_wrapper_init(311): completed
6.c 6421 set_ipv6
====== RTK PCM Controller Initialization =======
_policy_route> [Request IRQ for PCM Controller OK!.
mUpdate source roWait 0s for PSDS_RGB8:0xf550a05c, value = 0x00005c01
uting for ifname Set command ID to 0xf
(ppp0), table(512================= PCM FINISH ===============
)
RTW: __ __ ____ ___ ___ __ __
ssp_pinctrl_init
RTW: \ \ / /| ___|/ \ / \ | \ | |
RTW: \ \/\/ / | __|| O | | O || |\\| |
pinctrl-rtk-elnath f4320428.pinctrl: elnath_set_mux: pinmux group:pcm_group reg_off:0x8 bit_off:24
RTW: \_/\_/ |_| \___/ \___/ |__| \__|
RTW:
RTW: [WFO]............................................DONE
ssp_dbg_probe: Enter
br0: port 7(wlan0) entered blocking state
br0: port 7(wlan0) entered forwarding state
ssp_dbg_probe: 1371, audio 000000006580a452
SSP_DBG HW ver 2
route: SIOCADDRT:RTW: setkey_hdl: set group key for 02:00:00:00:00:41, kid:1 type:1 algo:AES
File exists
RTNETLINK answers:RTW: setkey_hdl: set group key for 02:00:00:00:00:41, kid:4 type:2 algo:BIP_CMAC_128
No such file or RTW: rtw_ndev_init(wlan0-vap0) if2 mac_addr=02:00:00:00:00:03
directory
br0: port 4(wlan0-vap0) entered blocking state
br0: port 4(wlan0-vap0) entered disabled state
device wlan0-vap0 entered promiscuous mode
RTW: rtw_update_sw_cap : sw_role_cap->bf_cap 0
iptables: No chaiPHL: Creating VAP with M-BSSID 1.
n/target/match bycipher: running self-test for cipher null cipher
that name.
cipher: allocating cipher with key length 0
cipher: testing encryption
cipher: initializing null cipher
cipher: plaintext:
cipher: ciphertext:
cipher: testing decryption
cipher: initializing null cipher
cipher: ciphertext:
iptables: Chain acipher: plaintext:
lready exists.
cipher: allocating cipher with key length 0
iptables: Chain acipher: random plaintext length 25
lready exists.
cipher: plaintext: 2153b6ad1e4e4b8370dd79272a53ef7ab5993c60a447ddc9d6
cipher: initializing null cipher
cipher: ciphertext: 2153b6ad1e4e4b8370dd79272a53ef7ab5993c60a447ddc9d6
cipher: initializing null cipher
cipher: plaintext[2]: 2153b6ad1e4e4b8370dd79272a53ef7ab5993c60a447ddc9d6
[add_ttnet_appbascipher: random plaintext length 2
ed_qos_rule:8698]cipher: plaintext: 6123
MIB_IP_QOS_TBL dcipher: initializing null cipher
oes't support thicipher: ciphertext: 6123
s template now
PHL: Config role #1 of type 3. MBSSID: 1.
cipher: initializing null cipher
RTW: [PHL STA]- role-idx: 1
cipher: plaintext[2]: 6123
RTW: [PHL STA]- mac_addr:02:00:00:00:00:42
RTW: [PHL STA]- aid: 0
RTW: [PHL STA]- macid: 1
RTW: [PHL STA]- wifi_band: 0
cipher: running self-test for cipher aes integer counter mode
RTW: [PHL STA]- bw: 0
RTW: [PHL STA]- chan: 0
RTW: [PHL STA]- offset: 0
cipher: testing encryption
RTW: [TXSC] clear txsc entry
cipher: plaintext: 0000000000000000000000000000000000000000000000000000000000000000
cipher: ciphertext: e03ead0935c95e80e166b16dd92b4eb4d23513162b02d0f72a43a2fe4a5f97ab
RTW: change mode, old_mode=2, new_mode=4, fw_state=0x8
cipher: testing decryption
RTW: rtw_set_802_11_infrastructure_mode(wlan0-vap0)Start AP mode! (1)
cipher: ciphertext: e03ead0935c95e80e166b16dd92b4eb4d23513162b02d0f72a43a2fe4a5f97ab
RTW: [TXSC_INIT][wlan0-vap0] a4_enable:0, a4_sta_list/a4_gptr_tbl init.
cipher: plaintext: 0000000000000000000000000000000000000000000000000000000000000000
RTW: [TXSC_INIT][wlan0-vap0] txsc:1, txsc_amsdu:1 amsdu_mode:1
RTW: [RXSC_INIT][wlan0-vap0] rxsc:1
cipher: random plaintext length 40
RTW: [rtl_wfo_fc_callback_hook_update]: ifname=wlan0-vap0, up=1, client_mode=0, do_nat25=0
cipher: plaintext: 735847026a2a8831d5dfb47868052b7ecd66d1a7dfe785594af779b262c0a258ba9d4e9304d539bb
RTW: wlan0-vap0 has no STA. Not issue BC deauth.
cipher: ciphertext: cacb7d82c5082c5984116222718ee40a40cb2e8a83e743f104578d917f87584dc40ef958587b061e
cipher: plaintext[2]: 735847026a2a8831d5dfb47868052b7ecd66d1a7dfe785594af779b262c0a258ba9d4e9304d539bb
cipher: random plaintext length 29
cipher: plaintext: 1807a5cc2536ecac18b26a8fc7c66b4e358dea7c9b8e16bcd8767b67ae
cipher: ciphertext: ffd0066b5c347faf73c52233ec37f5b2b0a5084c48a59afeef436285f2
cipher: plaintext[2]: 1807a5cc2536ecac18b26a8fc7c66b4e358dea7c9b8e16bcd8767b67ae
cipher: running self-test for cipher aes cipher block chaining (cbc) mode
cipher: testing encryption
cipher: plaintext: 00112233445566778899aabbccddeeff
cipher: ciphertext: 69c4e0d86a7b0430d8cdb78070b4c55a0335ed2767f26df164832e234438708b
cipher: testing decryption
cipher: ciphertext: 69c4e0d86a7b0430d8cdb78070b4c55a
RTW: Beacon BSS MAC: 02:00:00:00:00:42
cipher: plaintext: 00112233445566778899aabbccddeeff
RTW: [rtw_build_he_supp_mcs] info_len:8
cipher: random plaintext length 54
RTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
cipher: plaintext: c7f22a8b25259a7c48862232946ecb259316508b37542b8dfe1122255b4401e2bbfec53739429c19fbe7d5e0ab864128d081dd97dde9
RTW: IE CH(36) BW(3) OF(1)
cipher: ciphertext: aa80aca92cd16ca6e7a8e1613af3211c8cd776f70a866aa6fb0d3b71e5790e9cdf367ea88813876f19fdae29e327c1bd8bbbefd1a4104fb0d4d9ee089b879762
RTW: start_bss_network: Affffffc012439000, C(0) B(-1) O(-1)
cipher: plaintext[2]: c7f22a8b25259a7c48862232946ecb259316508b37542b8dfe1122255b4401e2bbfec53739429c19fbe7d5e0ab864128d081dd97dde9
cipher: random plaintext length 2
cipher: plaintext: 9b22
RTW: update_wireless_mode(wlan0-vap0) chan=36, network_type=22, wireless_mode=22(3f)
cipher: ciphertext: e0b1ce6af0103f44661cdd91ce97bf7f
cipher: plaintext[2]: 9b22
auth func: running self-test for auth function null authentication function
auth func: allocating auth func with key length 0
auth func: tag length 0
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x8
auth func: key:
auth func: data:
auth func: tag computed:
auth func: tag expected:
auth func: running self-test for auth function hmac sha-1 authentication function
auth func: key: 0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
sh: auth func: data: 4869205468657265
can't open '/etc/auth func: tag computed: b617318655057264e28bc0b6fb378c8ef146be00
scripts/rps.sh'
auth func: tag expected: b617318655057264e28bc0b6fb378c8ef146be00
RTW: assoc success
INITIAL VOIP DSP PROGRAM
PHL: [MAC] mac_set_bcn_ignore_edcca: port(0), mbssid(1 ms), band(0), en/dis(1)
lock_main_pool init
lock_encdec init
INIT VAR OK
=== RTP Event Send Tasklet Initialization ===
RTW: setkey_hdl: set group key for 02:00:00:00:00:42, kid:1 type:1 algo:AES
========================================
RTW: setkey_hdl: set group key for 02:00:00:00:00:42, kid:4 type:2 algo:BIP_CMAC_128
wlan0: interface stIPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
ate ACS->ENABLED
wlan0: AP-ENABLEDbr0: port 4(wlan0-vap0) entered blocking state
br0: port 4(wlan0-vap0) entered forwarding state
timer is pending , treat as first query
RTNETLINK answers: No such file or directory
==> [addEthWANdev] /bin/smuxctl --if nas0 --rx --tags 0 --filter-unicast-mac 1 --rule-priority 900 --set-rxif nas0_1 --rule-alias nas0_1-rx-default-root --target ACCEPT --rule-append
RTNETLINK answers: No such file or directory
Error: ipv6: FIB table does not exist.
Flush terminated
voip_dsp_object_version_init(972) 82
VOIP_DSP_OBJECT_VERSION: VoIP-1.6-DSP-codec_on_arm-usdk_2.2.0-rev_5728-2026-01-28
[startConnection@31198] pEntry->ifIndex = 130817, pEntry->cmode = 1
1483 MER
[start_wifi_priv_cfg 801] 0 wlanDisa[33mAdd RFC2833 TX Timer
[0m
bled=0
[start_wRTW: [TXSC] clear txsc entry
ifi_priv_cfg 818]RTW: [core_mib_txforce][txforce] macid:0, fix_rate = 0xffff
& launch: wlan_idPHL: LIFETIME: band 0
x = 0
iptables:PHL: MGQ: en 0 val 0
Chain already exPHL: ACQ: en 0 val 0 0 0 0
ists.
RTW: [TXSC] clear txsc entry
RTW: [TXSC] clear txsc entry
RTW: [TXSC] clear txsc entry
RTW: [rtw_build_he_supp_mcs] info_len:8
RTW: [rtw_build_he_supp_mcs] info_len:8
PHL: [MAC] mac_set_bcn_ignore_edcca: port(0), mbssid(1 ms), band(0), en/dis(1)
RTW: beacon ignore edcca: 1
RTW: core_mib_power_percent(1529)set ref power, percent: 100, diff: 0
RTW: core_mib_power_ref(1554)set ref power, txagc_ref: 0
RTW: core_mib_power_limit(1580)set power limit: 0
RTW: [rtw_build_he_supp_mcs] info_len:8
RTW: [rtw_build_he_supp_mcs] info_len:8
ip6tables: Chain already exists.
[start_wifi_priv_cfg 801] 0 wlanDisabled=1
[restart_upnp:23267] miniupnpd parameter error! (parameter=0, 1, 130817, 0, upnpItf=65536)
[add_ttnet_appbased_qos_rule:8698] MIB_IP_QOS_TBL does't support this template now
/bin/sh: can't create /sys/class/net/wlan0-vap1/brport/hairpin_mode: nonexistbr1: port 4(wlan0.46) entered blocking state
ent directory
[sbr1: port 4(wlan0.46) entered disabled state
tart_wifi_priv_cfg 801] 0 wlanDisabled=1
/bin/sh: can't create /sys/class/net/wlan0-vapdevice wlan0.46 entered promiscuous mode
2/brport/hairpin_mode: nonexistent directory
[start_wifi_priv_cfg 801] 0 wlanDisabled=1
/bin/sh: can't cRTW: core_mib_power_percent(1529)set ref power, percent: 100, diff: 0
reate /sys/class/br1: port 4(wlan0.46) entered blocking state
net/wlan0-vap3/brbr1: port 4(wlan0.46) entered forwarding state
port/hairpin_mode:IPv6: ADDRCONF(NETDEV_CHANGE): br1: link becomes ready
nonexistent directory
==> [addEthWANdev] /bin/smuxctl --if nas0 --rx --tags 1 --filter-vid 0x2e 1 --filter-unicast-mac 1 --rule-priority 900 --set-rxif nas0_2 --rule-alias nas0_2-rx-default-root --target ACCEPT --rule-append
==> [addEthWANdev] /bin/smuxctl --if nas0 --rx --tags 2 --filter-vid 0x2e 1 --filter-unicast-maRTW: ERROR update_mgntframe_attrib bmc_sta=NULL
c 1 --rule-prioriRTW: [TXSC] clear txsc entry
ty 900 --set-rxifRTW: [core_mib_txforce][txforce] macid:0, fix_rate = 0xffff
nas0_2 --rule-alRTW: [TXSC] clear txsc entry
ias nas0_2-rx-defRTW: [TXSC] clear txsc entry
ault-root --targeRTW: [TXSC] clear txsc entry
t ACCEPT --rule-aRTW: ERROR [core_mib_edcca_mode] should be config after iface up
ppend
/bin/sh: can't create /sys/cRTW: core_mib_power_percent(1534), interface is not running
lass/net/wlan0-vxRTW: core_mib_power_ref(1558), interface is not running
d/brport/hairpin_RTW: core_mib_power_limit(1584), interface is not running
mode: nonexistent directory
[start_wifi_priv_cfg 801] 1 wlanDisabled=0
[start_wifi_priv_cfg 818]& launch: wlan_idx = 1
[1] wlanDisabled=0
gen_hapd_cfg
[get_wifi_conf][645][if_idx = 1] [index = 0]++
config->encrypt=4 psk_enable=2 authtype=2 encmode=2 psk_format=0 gk_rekey=86400
enEzpwAvSN3S
wpa_cipher=0x0 wpa2_cipher=0x2 enable_1x=0
dot11IEEE80211W=1 enableSHA256=0
sae_pwe=0
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+6 = 40
[get_wifi_vif_conf][70], if_idx=1 index=1
[get_wifi_vif_conf][70], if_idx=1 index=2
[get_wifi_vifRTW: [rtw_hw_start 882] Start flash process !!
_conf][70], if_idPHL: RP agg is 121 for 640.
x=1 index=3
[getPHL: hal_cfg_fw_8192xb : fw_en 1.
_wifi_vif_conf][70], if_idx=1 index=4
wlan1 VAP1 disabled
wlan1 VPHL: [MAC] efuse_fv = 0xff
AP2 disabled
wPHL: [MAC] [MAC-INFO]- CV : 1
lan1 VAP3 disablePHL: [MAC] [MAC-INFO]- FV : 0
d
wlan1 VAP4 disabled
launch haPHL: [MAC] efuse_aid = 0xffff
pd: wlan_idx = 1 PHL: [MAC] [MAC-INFO]- AID : 6816
launch_hapd_by_cmd(7143) echo 0 into wlan1 coex_2g_40m
sh: can't crePHL: [MAC] Clear all bd index done.
ate /proc/net/rtkPHL: [MAC] [FWDL] FW INIT......................................START
_wifi6/wlan1/coexPHL: [MAC] Downloading Chip Halmac ID: 0x03
_2g_40m: nonexistPHL: [MAC] [FWDL] Query Internal FW Chip_ID = 0x3
ent directory
==PHL: [MAC] [FWDL] Query Internal FW CV = 0x1
> [addEthWANdev] PHL: [MAC] [FWDL] Query Internal FW cat = 0x2
/bin/smuxctl --ifPHL: [MAC] [FWDL] WCPU OFF......................................DONE
nas0_2 --tx --taPHL: [MAC] [FWDL] WCPU FWDL Boot.
gs 0 --push-tag -PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
-set-vid 0x2e 1 -PHL: [MAC] [FWDL] WCPU FW BIN CHECK.............................DONE
-target ACCEPT --PHL: [MAC] [FWDL] WCPU PRE BOOT..................................DONE
rule-alias nas0_2PHL: [MAC] [FWDL] WCPU IMAGE HEADER SEND........................DONE
-tx-default --rulPHL: [MAC] [FWDL] SEC_0:Len=0x5BD88,Addr=0x20100000,Type=0x2
e-append
rfkill:PHL: [MAC] [FWDL] SEC_1:Len=0x1CE8,Addr=0x2015BD88,Type=0x7
Cannot open RFKIPHL: [MAC] [FWDL] SEC_2:Len=0x4530,Addr=0x2021B000,Type=0x1
LL control devicePHL: [MAC] [FWDL] SEC_3:Len=0x3C0,Addr=0x20237C00,Type=0x9
==> [addEthWANdPHL: [MAC] [FWDL] DLFW DONE (0x8)
ev] /bin/smuxctl --if nas0_2 --tx --tags 1 --set-vid 0x2e 1 --target ACCEPT --rule-alias nas0_2-tx-default --rule-append
==> [addEthWANdev] /bin/smuxctl --if nas0_2 --tx --tags 2 --set-vid 0x2e 2 --target ACCEPT --rule-alias nas0_2-tx-default --rule-append
PHL: [MAC] [FWDL] INIT SYSMIB ENTRY (0xA)
PHL: [MAC] [FWDL] WCPU RAM PATCH.................................DONE
PHL: [MAC] _____ _____ _ ___ _ ___ ___
PHL: [MAC] | __\ \ / / \| | | _ \/_\ / __/ __|
PHL: [MAC] | _| \ \/\/ /| |) | |__ | _/ _ \\__ \__ \
PHL: [MAC] |_| \_/\_/ |___/|____| |_|/_/ \_\___/___/
PHL: [MAC] [FWDL] OS START DONE (0x26)
PHL: [MAC] [FWDL] WCPU FREERTOS INIT.............................DONE
PHL: [MAC] ___ _____ ___ ___ ___ ___ ___ _____
PHL: [MAC] | _ |_ _/ _ \/ __| | _ )/ _ \ / _ |_ _|
PHL: [MAC] | / | || (_) \__ \ | _ | (_) | (_) || |
PHL: [MAC] |_|_\ |_| \___/|___/ |___/\___/ \___/ |_|
PHL: [MAC] [FWDL] Image Git SHA = C57AEABE
PHL: [MAC] [FWDL] FW INIT.......................................DONE
PHL: hal_mac_print_fw_version: FW version V0.27.112.5, Ready
PHL: ERROR _hal_mac_get_ofld_cap : disable fw ofld cmd!
PHL: Set RX packet size filter to 4096B
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PHY_REG.txt" (2835/28679) OK.
sh: can't open '/etc/scripts/rps.sh'
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PHY_REG_GAIN.txt" (257/3711) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/RadioA.txt" (1009/11599) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/RadioB.txt" (823/9230) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/TXPWR_ByRate.txt" (94/2327) OK.
sh: can't open '/etc/scripts/rps.sh'
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/TXPWR_TrackTSSI.txt" (671/2485) OK.
PHL: _hal_dl_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/TXPWR_LMT.txt" (4452/24931) OK.
sh: can't open '/etc/scripts/rps.sh'
unlink /var/interface/uptime/nas0_1
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/PHY_REG.txt" (21/298) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/PHY_REG_GAIN.txt" (1/54) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/RadioA.txt" (3/72) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/RadioB.txt" (3/72) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/TXPWR_ByRate.txt" (94/2311) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/TXPWR_TrackTSSI.txt" (671/2469) OK.
PHL: _hal_dl_ext_para_file:: Download file "/etc/conf/rtl8192xbe/RFE50/PON_2G/TXPWR_LMT.txt" (4452/24944) OK.
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x0
argc 1, slicinitpowReset SSP
er 1
elnath_pmx_request_gpio: pin:138 reg_off:0x10 bit_off:10
PHL: rtw_hal_mac_fw_log_cfg: level 4, output 0x00000002, comp 0x00000004, comp ext 0x00000000.
Pull high GPIO 138
PHL: rtw_hal_mac_fw_log_cfg: level 4, output 0x00000002, comp 0x00000004, comp ext 0x00000000.
PHL: rtw_hal_mac_fw_log_cfg: level 4, output 0x00000002, comp 0x00000004, comp ext 0x00000000.
PHL: rtw_hal_start: Get MAC(0xd200) ok!!! 0x00000000
PHL: Set regular_idx:2 (REGULATION_FCC)
PHL: Set MAC(0xd200) ok!!! 0x00000000
RTW: rtw_update_sw_cap : sw_role_cap->bf_cap 204
PHL: Config role #0 of type 2. MBSSID: 0.
PHL: Initializing port 0 with 0 M-BSSID.
RTW: [PHL STA]- role-idx: 0
RTW: [PHL STA]- mac_addr:02:00:00:00:00:40
RTW: [PHL STA]- aid: 0
RTW: [PHL STA]- macid: 0
RTW: [PHL STA]- wifi_band: 0
RTW: [PHL STA]- bw: 0
RTW: [PHL STA]- chan: 0
RTW: [PHL STA]- offset: 0
RTW: [rtw_hw_iface_init] enable interrupt in the END of init
mask: 0x25000000, 0x00180005, 0x00000000, 0x00600000, 0x00000002
RTW: [TXSC] clear txsc entry
[_netdev_open] change tx_mode form 0 to 0
RTW: change mode, old_mode=2, new_mode=4, fw_state=0x8
RTW: rtw_set_802_11_infrastructure_mode(wlan1)Start AP mode! (1)
RTW: [TXSC_INIT][wlan1] a4_enable:0, a4_sta_list/a4_gptr_tbl init.
RTW: [TXSC_INIT][wlan1] txsc:1, txsc_amsdu:1 amsdu_mode:1
RTW: [RXSC_INIT][wlan1] rxsc:1
RTW: [rtl_wfo_fc_callback_hook_update]: ifname=wlan1, up=1, client_mode=0, do_nat25=0
br0: port 5(wlan1) entered blocking state
br0: port 5(wlan1) entered disabled state
device wlan1 entered promiscuous mode
wlan1: interface sRTW: [_rtw_sitesurvey_condition_check]Caller: cfg80211_rtw_scan on wlan1
tate UNINITIALIZED->COUNTRY_UPDATE
RTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
wlan1: interfacePHL: Set RX packet size filter to 4096B
state COUNTRY_UPRTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
DATE->HT_SCAN
Pull low GPIO 138
wlan1: Disable Tx Duty Cycle (ther_avg:4, state:init)
[startConnection@31198] pEntry->ifIndex = 130818, pEntry->cmode = 1
1483 MER
iptables: Chain already exists.
ip6tables: Chain already exists.
[restart_upnp:23267] miniupnpd parameter error! (parameter=0, 1, 130818, 0, upnpItf=65536)
Pull high GPIO 138
Start SLIC init....
init_spi_dev(index = 0)
init_spi_dev(spi_dev 00000000e55708c9)
move this action after init
devicePcn = [49], deviceRcn = [8]]
iptables v1.4.18: Couldn't load target `LXC_FWD_TBL':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `LXC_FWD_TBL':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
Illegal target name 'LXC_FWD_TBL'.
Chain 'LXC_FWD_TBL' doesn't exist.
iptables v1.4.18: Couldn't load target `LXC_IN_TBL':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `LXC_IN_TBL':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
Illegal target name 'wlan_map_block'.
Illegal target name 'wlan_map_block'.
Illegal target name 'map_portmapping'.
Illegal target name 'map_portmapping'.
RTNETLINK answers: File exists
[block_br_wan_forward:3690] Entry.cmode =2, Entry.IpProtocol=3
[block_br_wan_forward:3690] Entry.cmode =1, Entry.IpProtocol=3
[block_br_wan_forward:3690] Entry.cmode =1, Entry.IpProtocol=1
iptables v1.4.18: Couldn't load target `voip_chain':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
RTNETLINK answers: No such process
RTNETLINK answers: No such process
rtk_del_dhcp6s_pd_policy_route_and_file: rm /var/run/dhcp6s_lan_pd_route_nas0_1
[rtk_fc_ipv6_mvlan_loop_detection_acl_delete@4806]: ERROR! No such file or directory
RTNETLINK answers: No such process
sh: can't open '/etc/scripts/rps.sh'
sh: can't open '/etc/scripts/rps.sh'
iptables: No chain/target/match by that name.
unlink /var/interface/uptime/nas0_2
RTNETLINK answers: No such process
sh: can't open '/etc/scripts/rps.sh'
iptables: No chain/target/match by that name.
interface wlan1.46 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
All DSP Software Ready. VoIP Defer Init done.
smuxctl failed(ret=-1) return errno(19) No such device
[set_TR069_Firewall:9430] ifname=[nas0_1], bridge mode=0
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `interface_grouping_br0':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: Chain already exists.
iptables: No chain/target/match by that name.
ip6tables: Chain already exists.
ip6tables: No chain/target/match by that name.
ipset v7.5: The set with the given name does not exist
ipset v7.5: The set with the given name does not exist
ipset v7.5: The set with the given name does not exist
ipset v7.5: The set with the given name does not exist
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPreNatLB_ppp0':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPostNatLB_ppp0':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPreNatLB_nas0_1':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPostNatLB_nas0_1':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPreNatLB_nas0_2':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPostNatLB_nas0_2':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPreNatLB_nas0_3':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `portfwPostNatLB_nas0_3':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPreNatLB_ppp0':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPostNatLB_ppp0':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPreNatLB_nas0_1':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPostNatLB_nas0_1':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPreNatLB_nas0_2':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPostNatLB_nas0_2':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPreNatLB_nas0_3':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `dmzPostNatLB_nas0_3':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
/bin/ebtables -P macfilter_forw[32mFXS in LOW power mode[0m
ard RETURN
sh: cDEVIFNAME parser error
an't create /proc/fastbridge: nonexistent directory
Restart IPv6 Filter!
voip_set_rg_1p_tag
/bin/iptables -t mangle -A voip_remarking -o nas0_2 -p UDP --dport 5060 -j MARK --set-mark 0x70/0x70
/bin/iptables -t mangle -A voip_remarking -o nas0_2 -p UDP --sport 9000:9004 -j MARK --set-mark 0x70/0x70
Sorry, rule does not exist.
Sorry, rule does not exist.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
[setTmpBlockBridgeFloodPktRule 2668]restore RA in bridge fowward!
Sorry, rule does not exist.
RTW: wlan1 has no STA. Not issue BC deauth.
RTW: Beacon BSS MAC: 02:00:00:00:00:40
RTW: [rtw_build_he_supp_mcs] info_len:4
RTW: rtw_set_country_cmd country_code:"TR" mapping to chplan:0x3a
RTW: IE CH(11) BW(1) OF(3)
RTW: start_bss_network: Affffffc0139c2000, C(0) B(-1) O(-1)
RTW: update_wireless_mode(wlan1) chan=11, network_type=25, wireless_mode=25(3d)
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x8
rtw_phl_ru_set_ch_bw:
RTW: assoc success
PHL: [MAC] mac_set_bcn_ignore_edcca: port(0), mbssid(0 ms), band(0), en/dis(1)
RTW: setkey_hdl: set group key for 02:00:00:00:00:40, kid:1 type:1 algo:AES
br0: port 5(wlan1) entered blocking state
br0: port 5(wlan1) entered forwarding state
timer is pending , treat as first query
sh: can't open '/etc/scripts/rps.sh'
RTW: setkey_hdl: set group key for 02:00:00:00:00:40, kid:4 type:2 algo:BIP_CMAC_128
wlan1: interface state HT_SCAN->ENABLED
wlan1: AP-ENABLED
br1: port 5(wlan1.46) entered blocking state
br1: port 5(wlan1.46) entered disabled state
device wlan1.46 entered promiscuous mode
br1: port 5(wlan1.46) entered blocking state
br1: port 5(wlan1.46) entered forwarding state
sh: can't open '/etc/scripts/rps.sh'
sh: can't open '/etc/scripts/rps.sh'
Cannot find device "imq0"
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
disable ipqos!!!
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `car_filter_us':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `car_filter_ds':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `car_traffic_qos_us':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `car_traffic_qos_ds':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: Too many links.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `car_filter_us':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `car_filter_ds':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `car_traffic_qos_us':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `car_traffic_qos_ds':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: Too many links.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
Chain 'car_traffic_qos_ebt' doesn't exist.
Illegal target name 'car_traffic_qos_ebt'.
Chain 'car_traffic_qos_ebt' doesn't exist.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
[start_wifi_priv_cfg 801] 1 wlanDisabled=1
/bin/sh: can't create /sys/class/net/wlan1-vap0/brport/hairpin_mode: nonexistent directory
[start_wifi_priv_cfg 801] 1 wlanDisabled=1
/bin/sh: can't create /sys/class/net/wlan1-vap1/brport/hairpin_mode: nonexistent directory
[start_wifi_priv_cfg 801] 1 wlanDisabled=1
Cannot find device "imq0"
/bin/sh: can't create /sys/class/net/wlan1-vap2/brRTW: core_mib_power_percent(1529)set ref power, percent: 100, diff: 0
port/hairpin_mode: nonexistent directory
[start_wifi_priv_cfg 801] 1 wlanDisabled=1
/bin/sh: can't create /sys/class/net/wlan1-vap3/brport/hairpin_mode: nonexistent directory
Cannot find device "imq0"
/bin/sh: can't create /sys/class/net/wlan1-vxd/brport/hairpin_mode: nonexistent directory
do_restartLanV6Server - 693
do_cleanLanV6Server - 807
Cannot find device "imq0"
Cannot find device "imq0"
[update_monitor_list_file:26760] process_name = wlan_manager, action = 1
[WLAN_MANAGER] config: /var/wlan_manager.conf.
[WLAN_MANAGER] v2.0.
[setup_dhcpdv6_conf_with_single_br:818]
no prefix!! set tmp subnet conf
Internet Systems Consortium DHCP Server 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Config file: /var/dhcpd6.conf
Database file: /var/dhcpd6.leases
PID file: /var/run/dhcpd6.pid
Wrote 0 NA, 0 TA, 0 PD leases to lease file.
Multiple interfaces match the same subnet: br0 br1
Multiple interfaces match the same shared network: br0 br1
Bound to *:547
Listening on Socket/7/br0/fe80::/64
Sending on Socket/7/br0/fe80::/64
fscanf failed: stop_upnp 23192
[stop_upnp:23199] Stop miniupnpd! (wanIf=)
upnpctrl(down): MINIUPNPD is down
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Too many links.
iptables: Too many links.
[start_upnp:23169] Start miniupnpd! (wanIf=ppp0)
iptables: Bad rule (does a matching rule exist in that chain?).
route: SIOCADDRT: File exists
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
enable ipqos!!!
rtk_qos_classf_rules_upstream_setup:3863 EntryNum=1
/bin/iptables -t mangle -A qos_ip_us_rules_0 -j MARK --set-mark 0x90/0x801fff
/bin/iptables -t mangle -A qos_ip_us_app_rules -o nas0_2 -g qos_ip_us_rules_0
[1;33;46m<subr_qos_3.c 7346 setupIPQ> [mConfig QoS total upstream 1048568 Kbps downstream 1024000 Kbps
[1;33;46m<fc_api.c 4815 rtk_fc_total_upstream_bandwidth_set> [mbandwidth=1048568
iptables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_access':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_access':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by tnf_conntrack_pptp: unknown parameter 'ports' ignored
hat name.
[route_cfg_modify:14640] nextHop = 10.80.222.1, toDest=10.116.13.16/255.255.255.240, metric=0, ifname=nas0_1, forceNH=0
Error: Nexthop has invalid gateway.
Didn't allow deault route setting in static route configuration!
setupAlgOnOff:5421 ipsec_port ports=500,4500
modprobe: module nf_conntrack_ipsec not found in modules.dep
modprobe: module nf_nat_ipsec not found in modules.dep
conntrack v1.4.6 (conntrack-tools): unknown option `--dport'
Try `conntrack -h' or 'conntrack --help' for more information.
conntrack v1.4.6 (conntrack-tools): unknown option `--dport'
Try `conntrack -h' or 'conntrack --help' for more information.
setupAlgOnOff:5465 pptp_port ports=1723
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
setupAlgOnOff:5490 ftp_port ports=21
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
setupAlgOnOff:5514 tftp_port ports=69
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
setupAlgOnOff:5542 h323_port ports=17nf_conntrack_h323: unknown parameter 'ports' ignored
29,1720
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
setupAlgOnOff:5593 rtsp_port ports=554,8554
nf_conntrack_rtsp v0.7 loading
nf_nat_rtsp v0.7 loading
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
setupAlgOnOff:5620 sip_port ports=5060
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
conntrack v1.4.6 (conntrack-tools): 0 flow entries have been deleted.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `wlan_nosecurity_access':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file set dos:0x4001ff
or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_redirect':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `wlan_nosecurity_access':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
Chain 'wlan_block' doesn't exist.
Sorry, rule does not exist.
Chain 'guest_access' doesn't exist.
Illegal target name 'guest_access'.
Chain 'guest_access' doesn't exist.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `guest_access':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
smuxctl failed(ret=-1) return errno(19) No such device
ip6tables v1.4.18: Couldn't load target `guest_access':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
smuxctl failed(ret=-1) return errno(19) No such device
/bin/sh: can't create proc/igmp/ctrl/skbMarkExtraSwitchPortId: nonexistent directory
iptables: Chain already exists.
killall: wlan_schedule: no process killed
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 1 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 2 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 3 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 4 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 5 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 6 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 7 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 8 success ! (ret = 0)
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `LAN_SYN_FLOOD_PROOF':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -s 192.168.1.0/24 -d 192.168.1.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -d 192.168.1.1 --dport 80 -j DROP
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -s 192.168.4.0/24 -d 192.168.4.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -d 192.168.4.1 --dport 80 -j DROP
/bin/sh: can't create proc/igmp/ctrl/skbMarkExtraSwitchPortId: nonexistent directory
Sorry, rule does not exist.
Sorry, rule does not exist.
Chain 'portmapping_nas0_0_out' doesn't exist.
Chain 'portmapping_nas0_0_in' doesn't exist.
Chain 'portmapping_nas0_1_out' doesn't exist.
Chain 'portmapping_nas0_1_in' doesn't exist.
Chain 'portmapping_nas0_2_out' doesn't exist.
Chain 'portmapping_nas0_2_in' doesn't exist.
[setTmpBlockBridgeFloodPktRule 2668]restore RA in bridge fowward!
Sorry, rule does not exist.
device br1 already exists; can't create bridge with the same name
[1;33;46m<utility.c 1185 setup_mac_addr> [mmacAddr[5]+5 = 3f
[1;33;46m<subr_net.c 16762 set_ipv4_lan_policy_route> [mSet IPv4 LAN route for ifname (br1), table(260)
iptables: Chain already exists.
iptables: Bad rule (does a matching rule exist in that chain?).
do_restart_dnsrelay:5379 no delay dns
Start udhcpd server!
Run Server function only
dhcpd server read configfile:poolname=default
dhcpd server read configfile:poolname=Conditional
dhcpd server read configfile:poolname=Voip Group
[update_monitor_list_file:26760] process_name = udhcpd, action = 1
Listening on Socket/br1
Sending on Socket/br1
Listening on Socket/br0
Sending on Socket/br0
[update_monitor_list_file:26760] process_name = dnsmasq, action = 0
[MIB] delay commit CURRENT_SETTING ...
[cfg_mib_update_ex:593] _mib_update(8) commitnow=1 (check_commit=0) success
[update_monitor_list_file:26760] process_name = dnsmasq, action = 1
killall lanNetInforestart lanNetInfoError ioctl in SIOCETHTEST errno=19(No such device)
Error ioctl in SIOCETHTEST errno=19(No such device)
Error ioctl in SIOCETHTEST errno=19(No such device)
[41;33m ===> Do startNTP<=== [0m
rm: can't remove '/var/localtime': No such file or directory
[main 4792] wan port power up!
ubi0 error: ubi_open_volume: cannot open device 0, volume 0, error -16
voip flash server share size = 11527
rcm_voip_get_ctype_interface
++++++The size of voipConfig 10811
voip omci line state share size = 53756
codec_suporrt_list 1039
[update_monitor_list_file:26760] process_name = boa, action = 1
[32m ===> Do Restart Multi-ap <=== [0m
[32m ===> multi_ap_restart_thread_func enter<=== [0m
<bind_web_socket:375> socket:4, ip_ver:6, port:443
[initLanNetInfoData 4225]:init LanNetInfoData.
[HPAV][set_hpav_monitorLogLevel:51] Set level 3
Multi_AP_Service is starting, profile number is : 4
<bind_web_socket:375> socket:10, ip_ver:6, port:80
Illegal target name 'wlan_map_block'.
======> [fm_apply_work] wait request....
Chain 'wlan_map_block' doesn't exist.
Chain 'wlan_map_block' doesn't exist.
Illegal target name 'map_portmapping'.
======> [fm_apply_work] wait request....
sh: can't create /proc/dos_syslog: nonexistent directory
Illegal target name 'wlan_map_block'.
Chain 'wlan_map_block' doesn't exist.
Chain 'wlan_map_block' doesn't exist.
Illegal target name 'map_portmapping'.
Cannot open DPP Credential /tmp/dpp_csign_key file.
Cannot open DPP Credential file.
Fail to read all DPP creds info, removing partial dpp crendentials !
[CONFIG] VLAN Configuration is disabled!
[CONFIG] map_supported_service is 1
[fill_channel_preference][430] Fail open chan_pref file !
[Map] Fail to load chan_pref, use legacy channel pref !
Multi AP controller daemon is running with 0
max_log_size is: 100 kB
[CONFIG-EXT] backhaul_sta_radio_index is 0
[CONFIG-EXT] backhaul_switch is 0
[CONFIG-EXT] check_interval is 0
[CONFIG-EXT] link_down_threshold is 0
[CONFIG-EXT] discovery_down_threshold is 0
[CONFIG-EXT] arp_loop is 0
[CONFIG] map_supported_service is 1
Multi AP checker is running with 0
[main 1305]:map_checker_debug on : 0, bridge name : br0
max_log_size is: 100 kB
killall: map_info_hub: no process killed
ps for map_controller found, pid is 4522
set dos:0x4001ff
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 1 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 2 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 3 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 4 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 5 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 6 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 7 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 8 success ! (ret = 0)
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `LAN_SYN_FLOOD_PROOF':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
[set_TR069_Firewall:9430] ifname=[nas0_1], bridge mode=0
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -s 192.168.1.0/24 -d 192.168.1.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -d 192.168.1.1 --dport 80 -j DROP
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -s 192.168.4.0/24 -d 192.168.4.1 --dport 80 -j ACCEPT
sh: can't create /proc/br_igmpsnoop: nonexistent directory
sh: can't create /proc/br_igmpquery: nonexistent directory
sh: can't create /proc/br_mldsnoop: nonexistent directory
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -d 192.168.4.1 --dport 80 -j DROP
sh: can't create /proc/br_mldquery: nonexistent directory
cwmp_flag=30
<main.c>Set No Debug Message!
<cwmp_utility.c>Set No Debug Message[1]
<main.c>Set Delay!
<cwmp_utility.c>Set Delay[18]
<main.c>Set DisConReqAuth!
<cwmp_utility.c>Set DisConReqAuth[1]
<cwmp_utility.c>Set gPrintSoap[0]
<cwmp_utility.c>Set gsupportPOST[0]
<cwmp_utility.c>Set gRandomInform[0]
<cwmp_utility.c>Set gLibUseIpv6[1]
<cwmp_utility.c>Set gEnableTimeZone[1]
<main.c,194>[cwmp]begin handle signal thread
[update_monitor_list_file:26760] process_name = cwmpCliUsage:
ent, action = 1
Enable unkown multicast data flooding:
enter cwmp_mainecho 1 > proc/fc/ctrl/igmp_unkonwn_flood
!
Root is InternDisable unkown multicast data flooding:
etGatewayDevice.
echo 0 > proc/fc/ctrl/igmp_unkonwn_flood
Start cwmp_main() status:disable
!
========== CWMP library ==========
c95b307
Thu Jul 30 18:52:14 2026 +0800
[ENH][TR] add mib flag to control the device for TR debug to print. (commit 2/2)
Build time: 20260920_15:42:22
==================================
<port_update_CWMP_diagnose_status:6204> diagnose_type = 1, status_code = 0
Unkown chip 9607f000
IGMP Snooping: enabled
MLD Snooping: enabled
[1;33;46m<subr_net.c 16762 set_ipv4_lan_policy_route> [mSet IPv4 LAN route for ifname (br1), table(260)
RTNETLINK answers: File exists
{
"process": "error",
"main_thread": "error",
"ubus": "none",
"mem": "none",
"msg": "none",
"trace msg 0": "Invalid_cmdu",
"trace msg 1": "Invalid_cmdu",
"trace msg 2": "Invalid_cmdu",
"trace msg 3": "Invalid_cmdu",
"trace msg 4": "Invalid_cmdu",
"trace msg 5": "Invalid_cmdu"
}
[32m ===> multi_ap_restart_thread_func exit! <=== [0m
Cannot find device "imq0"
Cannot find device "nas0_3"
disable ipqos!!!
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `car_filter_us':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `car_filter_ds':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `car_traffic_qos_us':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `car_traffic_qos_ds':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: Too many links.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `car_filter_us':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `car_filter_ds':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `car_traffic_qos_us':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.18: Couldn't load target `car_traffic_qos_ds':No such file or directory
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: Too many links.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
Chain 'car_traffic_qos_ebt' doesn't exist.
Illegal target name 'car_traffic_qos_ebt'.
Chain 'car_traffic_qos_ebt' doesn't exist.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
Error: Cannot delete qdisc with handle of zero.
Cannot find device "nas0_3"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "imq0"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
Cannot find device "nas0_3"
enable ipqos!!!
rtk_qos_classf_rules_upstream_setup:3863 EntryNum=1
/bin/iptables -t mangle -A qos_ip_us_rules_0 -j MARK --set-mark 0x90/0x801fff
/bin/iptables -t mangle -A qos_ip_us_app_rules -o nas0_2 -g qos_ip_us_rules_0
[1;33;46m<subr_qos_3.c 7346 setupIPQ> [mConfig QoS total upstream 1048568 Kbps downstream 1024000 Kbps
[1;33;46m<fc_api.c 4815 rtk_fc_total_upstream_bandwidth_set> [mbandwidth=1048568
iptables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory
Tryset dos:0x4001ff
`ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 1 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 2 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 3 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 4 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 5 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 6 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 7 success ! (ret = 0)
rtk_fc_ddos_tcp_syn_rate_limit_delete: delete syn flood acl rule 8 success ! (ret = 0)
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
[1;33;46m<fc_api.c 1226 rtk_qos_share_meter_get> [mrt_rate_shareMeterType_get already exist !
iptables: No chain/target/match by that name.
iptables v1.4.18: Couldn't load target `LAN_SYN_FLOOD_PROOF':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -s 192.168.1.0/24 -d 192.168.1.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br0 -p TCP --tcp-flags SYN SYN -d 192.168.1.1 --dport 80 -j DROP
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -s 192.168.4.0/24 -d 192.168.4.1 --dport 80 -j ACCEPT
/bin/iptables -A LAN_SYN_FLOOD_PROOF -i br1 -p TCP --tcp-flags SYN SYN -d 192.168.4.1 --dport 80 -j DROP
echo 0xfffa > /proc/loopback_detect_ethtype
loop_eth_type=0xfffa
fscanf failed: stop_upnp 23192
[stop_upnp:23199] Stop miniupnpd! (wanIf=)
loopback: LoopExistPeriod = 5
loopback: LoopCancelPeriod = 300
loopback: EthernetType = 0xFFFA
loopback: vid = upnpctrl(down): MINIUPNPD is down
untagged
total 1 vlan values
enable loopback detect
iptables: No chain/target/match by that name.
[start_upnp:23169] Start miniupnpd! (wanIf=ppp0)
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
route: SIOCADDRT: File exists
do_restartLanV6Server - 693
do_cleanLanV6Server - 807
sh: can't open '/etc/scripts/rps.sh'
0
[update_monitor_list_file:26760] process_name = inetd, action = 1
[update_monitor_list_file:26760] process_name = systemd, action = 1
[update_monitor_list_file:26760] process_name = lanNetInfo, action = 1
===== monitord =====
Debug message: off
Monitor Timer: 15 sec.
BusyBox v1.22.1 (2026-09-20 15:18:03 CST) multi-call binary.
Usage: rm [-irf] FILE...
Remove (unlink) FILEs
-i Always prompt before removing
-f Never prompt
-R,-r Recurse
cmd:echo 0 >/sys/bus/usb/devices/usb1/authorized
cmd:echo 0 >/sys/bus/usb/devices/usb2/authorized
cmd:echo 1 >/sys/bus/usb/devices/usb1/authorized
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: authorized to connect
cmd:echo 1 >/sys/bus/usb/devices/usb2/authorized
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: authorized to connect
/usr/share/lxc/templates/lxc-busybox: line 351: file: not found
warning : busybox is not statically linked.
warning : The template script may not correctly
warning : setup the container environment.
[setup_dhcpdv6_conf_with_single_br:818]
no prefix!! set tmp subnet conf
Internet Systems Consortium DHCP Server 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Config file: /var/dhcpd6.conf
Database file: /var/dhcpd6.leases
PID file: /var/run/dhcpd6.pid
Wrote 0 NA, 0 TA, 0 PD leases to lease file.
Bound to *:547
Listening on Socket/7/br0/fe80::/64
Sending on Socket/7/br0/fe80::/64
fscanf failed: stop_upnp 23192
[stop_upnp:23199] Stop miniupnpd! (wanIf=)
upnpctrl(down): MINIUPNPD is down
iptables: No chain/target/match by that name.
[start_upnp:23169] Start miniupnpd! (wanIf=ppp0)
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.18: Couldn't load target `MINIUPNPD':No such file or directory
Try `iptables -h' or 'iptables --help' for more information.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
route: SIOCADDRT: File exists
setting root password to "root"
Password for 'root' changed
'dropbear' ssh utility installed
System startup success !
[main 5526] lan port power down!
[MIB] delay commit CURRENT_SETTING ...
[cfg_mib_update_ex:593] _mib_update(8) commitnow=1 (check_commit=0) success
[41;33m ===> Do flow flush <=== [0m
0
0
rt_port_phyPowerDo[1;33;41mextGphy: !!!No driver support for PHY at addr 7 [rtk_ext_gphyPortPowerDown_set(line 2069)][m
wn_set(4, 0) failed: set_lan_port_powerdown_state 1691
rt_port_phyPowerDown_set(5, 0) failed: set_lan_port_powerdown_state 1691
rt_port_phyPowerDown_set(7, 0) failed: set_lan_port_powerdown_state 1691
[main 5529] lan port power up!
[monitord inetd] died!
[startup]unknow reboot, record it.
[ttg reboot]record reboot event, cnt 19, date 01011970020102, reason 3
service /bin/dropbear port 22 tcp enabled
service /bin/ftpd port 21 tcp enabled
service /bin/tftpd port 69 udp enabled
RTW: start_bss_network: Affffffc0121bd000, C(36) B(3) O(0)
RTW: update_wireless_mode(wlan0) chan=36, network_type=22, wireless_mode=22(3f)
RTW: update_wireless_mode(wlan0-vap0) chan=36, network_type=22, wireless_mode=22(3f)
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x8
rtw_phl_ru_set_ch_bw:
[MIB] delay commit CURRENT_SETTING ...
[cfg_mib_update_ex:593] _mib_update(8) commitnow=1 (check_commit=0) success
start watch dog
launch /bin/VoIP_maserati at 81
ttl_number is 0
voip flash client share size = 11527
waiting voip flash server init...)
voip omci line state share size = 53756
codec_suporrt_list 1039
watch dog pipe mode
VoIP RCM LOG is ENABLED!!
Reset register status...
[32mdo_mgr_VOIP_MGR_CTRL_TRANSESSION_ID(1625): 0 255 255
[0m
ERROR: must check sip_config_read: dynamic_pt_check failed
ttl_number is 0
[33mcountry wasn't defined. Set to default SLIC impedance 600 ohm.
[0m
SLIC_RING_70V_25HZ
Vp886SetOptionRingingParams: pLineObj->refRingingBatV 75, swParam[1] 0x8E
Reset register status...
PHL: [MAC] band_idle_ck: cnt 2199, band 0, 0x8
Son düzenleyen: Moderatör:
