Son düzenleyen: Moderatör:
- Katılım
- 22 Aralık 2023
- Mesajlar
- 2.493
- Makaleler
- 1
- Çözümler
- 13
- Beğeniler
- 2.295
Desteklenmiyor.
Siz bu konuyu açtığınızda detseklenmiyordu. Şu anda yüklenebiliyor ama birçok özellik çalışmıyor. İleride tam destek gelir mi bilmiyorum.
Gelişmeleri buradan takip edebilirsiniz:
Kod:
bldr> xmdm 80020000 5f7e06
CC
bldr> jump 80020000
Jump to 80020000
zimage at: 800233C0 80616DC0
Uncompressing Linux at load address 81000000
Copy device tree to address 827976C0
Now, booting the kernel...
[ 0.000000] Linux version 6.12.59 (eigma@forge) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r31496-1cd3660bee) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Thu Dec 11 17:45:09 2025
[ 0.000000] ISPRAM0: PA=1c000000,Size=00010000,enabled
[ 0.000000] printk: legacy bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019558 (MIPS 34Kc)
[ 0.000000] MIPS: machine is TP-Link VC220-G3u
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s18096 r8192 d22864 u49152
[ 0.000000] Kernel command line:
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=000657b1
[ 0.000000] Readback ErrCtl register=000657b1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32768
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[ 0.000000] NR_IRQS: 256
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000002] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.008521] timer: using 200.000 MHz high precision timer
[ 0.014602] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032)
[ 0.081314] pid_max: default: 32768 minimum: 301
[ 0.096039] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.104028] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.122410] rcu: Hierarchical SRCU implementation.
[ 0.127665] rcu: Max phase no-delay instances is 1000.
[ 0.134448] smp: Bringing up secondary CPUs ...
[ 0.139420] smp: Brought up 1 node, 1 CPU
[ 0.143889] Memory: 103712K/131072K available (7433K kernel code, 622K rwdata, 1440K rodata, 15712K init, 227K bss, 26772K reserved, 0K cma-reserved)
[ 0.161871] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.172748] futex hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.188365] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.206431] clocksource: Switched to clocksource timer
[ 0.221838] NET: Registered PF_INET protocol family
[ 0.227446] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.236053] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.245258] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.253713] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.262131] TCP bind hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.269994] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.277580] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.285818] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.293017] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.301592] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.367024] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.376957] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.397383] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.405493] printk: legacy console [ttyS0] disabled
[ 0.411448] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 8, base_baud = 115200) is a 16550
[ 0.420993] printk: legacy console [ttyS0] enabled
[ 0.420993] printk: legacy console [ttyS0] enabled
[ 0.430990] printk: legacy bootconsole [early0] disabled
[ 0.430990] printk: legacy bootconsole [early0] disabled
[ 0.492593] spi-nand spi0.0: ESMT SPI NAND was found.
[ 0.497840] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.517378] en75_bmt: found BMT in block 1023
[ 0.658433] en75_bmt: found BBT in block 943
[ 0.662766] en75_bmt: BBT & BMT found
[ 0.666551] en75_bmt: blocks: total: 1024, user: 943, factory_bad: 0, worn: 0 reserve: 81
[ 0.674745] en75_bmt: 117 MiB usable space
[ 0.733816] 8 fixed-partitions partitions found on MTD device spi0.0
[ 0.744453] Creating 8 MTD partitions on "spi0.0":
[ 0.749301] 0x000000000000-0x000000020000 : "boot"
[ 0.755576] 0x000000020000-0x0000000a0000 : "romfile"
[ 0.764287] 0x0000000a0000-0x0000001a0000 : "config"
[ 0.772483] 0x0000001a0000-0x0000001e0000 : "radio"
[ 0.779374] 0x0000001e0000-0x0000023e0000 : "tclinux"
[ 0.814505] 0x0000003e0000-0x0000023e0000 : "rootfs"
[ 0.821492] mtd: setting mtd5 (rootfs) as root device
[ 0.827566] 1 squashfs-split partitions found on MTD device rootfs
[ 0.833782] 0x000001280000-0x0000023e0000 : "rootfs_data"
[ 0.841055] 0x0000023e0000-0x0000045e0000 : "tclinux_alt"
[ 0.876537] 0x0000045e0000-0x000007300000 : "openwrt_ubi"
[ 0.926766] NET: Registered PF_INET6 protocol family
[ 0.938876] Segment Routing with IPv6
[ 0.942667] In-situ OAM (IOAM) with IPv6
[ 0.946939] NET: Registered PF_PACKET protocol family
[ 0.952121] 8021q: 802.1Q VLAN Support v1.8
[ 0.995305] clk: Disabling unused clocks
[ 1.042799] Freeing unused kernel image (initmem) memory: 15712K
[ 1.048919] This architecture does not have kernel memory protection.
[ 1.055368] Run /init as init process
[ 1.569033] init: Console is alive
[ 1.594327] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 1.626177] usbcore: registered new interface driver usbfs
[ 1.631963] usbcore: registered new interface driver hub
[ 1.637481] usbcore: registered new device driver usb
[ 1.702435] SCSI subsystem initialized
[ 1.714907] usbcore: registered new interface driver usb-storage
[ 1.722390] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 1.732840] init: - preinit -
[ 4.566384] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.796879] procd: - early -
[ 9.396801] procd: - ubus -
[ 9.456151] procd: - init -
Please press Enter to activate this console.
[ 10.201516] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.240088] tun: Universal TUN/TAP device driver, 1.6
[ 10.258007] econet_eth: loading out-of-tree module taints kernel.
[ 10.277207] econet_eth 1fb50000.ethernet: eth0 using DT mac 5c:a6:e6:0d:f5:04
[ 10.285311] econet_eth 1fb50000.ethernet eth0: EcoNet frame engine at 0xbfb50000, irq 21
[ 10.371466] usbcore: registered new device driver r8152-cfgselector
[ 10.378013] usbcore: registered new interface driver r8152
[ 10.560883] PPP generic driver version 2.4.2
[ 10.577730] NET: Registered PF_PPPOX protocol family
[ 10.598915] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.836881] urngd: v1.0.2 started.
BusyBox v1.37.0 (2025-12-02 16:18:13 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r0+32198-e71a3458d0
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
OpenWrt recently switched to the "apk" package manager!
OPKG Command APK Equivalent Description
------------------------------------------------------------------
opkg install <pkg> apk add <pkg> Install a package
opkg remove <pkg> apk del <pkg> Remove a package
opkg upgrade apk upgrade Upgrade all packages
opkg files <pkg> apk info -L <pkg> List package contents
opkg list-installed apk info [ 36.961081] br-lan: port 1(eth0) entered blocking state
[ 36.966613] br-lan: port 1(eth0) entered disabled state
[ 36.972008] econet_eth 1fb50000.ethernet eth0: entered allmulticast mode
Li[ 36.979240] econet_eth 1fb50000.ethernet eth0: entered promiscuous mode
st installed packages
opkg update apk update Update package lists
opkg search <pkg> apk search <pkg> Search for packages
------------------------------------------------------------------
For more information visit:
https://openwrt.org/docs/guide-user/additional-software/opkg-to-apk-cheatsheet
root@OpenWrt:~# [ 37.075773] br-lan: port 1(eth0) entered blocking state
[ 37.081137] br-lan: port 1(eth0) entered forwarding state
uname -a
Linux OpenWrt 6.12.59 #0 SMP Thu Dec 11 17:45:09 2025 mips GNU/Linux
root@OpenWrt:~# cat /etc/openwroot@OpenWrt:~# cat /etc/openwrt_reroot@OpenWrt:~# cat /etc/openwrt_release
DISTRIB_ID='OpenWrt'
DISTRIB_RELEASE='SNAPSHOT'
DISTRIB_REVISION='r0+32198-e71a3458d0'
DISTRIB_TARGET='econet/en751221'
DISTRIB_ARCH='mips_24kc'
DISTRIB_DESCRIPTION='OpenWrt SNAPSHOT r0+32198-e71a3458d0'
DISTRIB_TAINTS='no-all'
root@OpenWrt:~#Gelişmeleri buradan takip edebilirsiniz:
Merhabalar, şu an bu versiyon kullanılabilir hale geldi mi? Ayrıca sadece root yetkisi ile yüklemek mümkün mü, yani telnet shell ile? Teşekkürler.
Son düzenleyen: Moderatör:
Kaplumbağa hızında ilerliyor. Geleceğini sanmıyorum.
Merhaba Recep Hocam, TP-Link VC220-G3u için Flash çipi ile ilgili DTS (Device Tree) ve ilgili sistem dosyalarını düzenlemeyi başardım. Şuanlık UART üzerinden yükleme ile cihaz kendi hazırladığım derleme ile kalıcı olarak openwrt yazılabiliyor ve boot oluyor. Dosya sistemi tarafını da çözmüş bulunmaktayım. hostname gibi sistem ayarları ve dosyalar flaş belleğe kalıcı olarak yazılabiliyor.
Projenin tamamlanmasına çok az kaldı ama maalesef şu an Ethernet ve Wi-Fi sürücülerinin/bağlantılarının çalışması konusunda takılmış durumdayım. Bu ağ arayüzlerinin dts veya sürücü/firmware entegrasyonu tarafında yardımcı olabilecek biri çıkarsa projeyi birlikte baya bir kısa sürede içinde finale ulaştırabileceğimizi umuyorum.
Not: Bu alanda yeni olduğum için desteğe ihtiyacım var. incelemek isteyen olursa logları veya OpenWRT build klasörünü gönderebilirim.
